Indesit IDC 75 S Installation, Where to install the tumble dryer Electrical connections

Installation

Where to install the tumble dryer

Electrical connections

EN	• Install the dryer far from gas
	ranges, stoves, radiators or
	hobs, as flames may damage it.
	If the dryer is installed below a
	worktop, ensure there are 10
	mm between the upper panel of
	the dryer and any objects
	above it, and 15 mm between
	the sides of the machine and
	the walls or furniture units
	adjacent to it. This ensures
	adequate air circulation.

10 mm

15 mm 15 mm

Before plugging the appliance into the socket, check the following:

• Make sure your hands are dry.

• The socket must have an earth connection.

• The socket must be able to withstand the machine’s

maximum power output as indicated on the data plate (see

Description of the tumble dryer).

• The power supply voltage must fall within the values indicated

on the data plate (see Description of the tumble dryer).

• The socket must be compatible with the dryer’s plug.

Should this not be the case, replace the plug or the socket.

￿ Do not use extension cords.

￿ The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if exposed to rain or storms.

￿ Once installed, the dryer’s electrical wire and plug must

Ventilation

•The room must be adequately ventilated while the dryer is running. Make sure that the dryer is installed in a room free of humidity and with adequate air circulation. The flow of air around the dryer is essential to allow water to condense during drying; the dryer will not function properly if it is placed in an enclosed space or inside a cabinet.

￿Some condensation may form if the dryer is used in a small or cold room.

￿We do not recommend installing the dryer in a cupboard; moreover, never install the machine behind a lockable, sliding or hinged door located on the opposite side of the dryer door.

Water drain

If your dryer is installed next to a drain the water can be plumbed into this drain. This does away with the need to empty the water container. If the dryer is stacked onto or installed next to a washing machine it can share the same drain. The height of the drain must be less than 3' (1 m) from the bottom of the dryer.

Remove existing hose from position shown in picture A and fit a suitable length of hose and connect as shown in picture B.

￿Make sure that the hose is not squashed or kinked when the dryer is in its final location.

be within reach.

￿ The power cord must not be bent or squashed.

￿ The power cord is supplied fitted with a BS1363 plug

and with a 13 amp BS1362 fuse. If it is necessary to fit a

replacement fuse, it must be a 13 Amp ASTA approved

to BS1362 type. WARNING: The plug must not be used

without a fuse cover. If a replacement fuse holder/cover is

required, it must be of the same colour coding or wording as

shown on the base of the plug.

Replacements are available from authorised dealers.

Moulded plug

Changing the plug

The wires in the power cord are coloured in accordance with the following.

Green and Yellow (Earth)			13A ASTA approved fuse
wire to terminal marked			to BS 1362.
“E”, symbol x, or coloured	GREEN &
green and yellow.	YELLOW
	BROWN	13 ampere fuse
			Brown (live) wire to teminal
Blue (Neutral) wire to	BLUE	CROSS-BAR	marked “L” or coloured
terminal marked ”N” or		CORD GRIP	red.
coloured black.

1

2

2

1

m

1

<

H

￿ If the plug being replaced is a non-rewirable type, then the

cut-off plug must be disposed of safely. DO NOT leave it where

it can be inserted into a socket and create a shock hazard.

￿ The power cord should be checked periodically and replaced

by a cord specially prepared for this dryer and fitted only by

authorized technicians (see Service). New or longer power

cords are supplied at an extra charge by authorized dealers.

￿ The manufacturer denies any responsibility should any

of these rules not be followed.

Picture A Picture B

￿ If in doubt about any of the above consult a qualified electrician.

Preliminary information

Once the tumble dryer is installed, clean the inside of the drum before operating it and remove any dirt accumulated during transportation.

4