Kalorik USK STP 20159 Using the Spray Bottle, Using the Pressing Cushion, Assembly page 7/24

Page 7

Fax +32 2 359 95 50

￿

Copies of the I/B. Please reproduce them without any changes except under special instruction from Team International BELGIUM. The pages must be reproduced and folded in order to obtain a booklet A5 (+/- 148.5 mm width x 210 mm height). When folding, make sure you keep the good numbering when you turn the pages of the I/B. Don’t change the page numbering. Keep the language integrity. Print only what is inside the frame.

PRESSING

Make sure the locking knob (2) is in the open position (UNLOCK).

Lift the handle (1). The pressing plate (4) moves to the up position.

Carefully arrange the garment to be pressed onto the ironing board (5).

Grasp the handle of the pressing plate(4) and lower it onto the ironing board (5), capturing the garment between the two halves of the steam press.

For lightly creased garments, simply lowering the handle and allowing the pressing plate to rest on the ironing board will be sufficient. Return to the open position. For very creased garments, continue to grasp the handle and press downward until the pressing plate is pushed to its lowest position, and then open the press.

If the temperature is set high enough you may give the fabric a burst of steam by pressing the burst of steam button (3) to remove stubborn wrinkles. Lower the pressing plate until it is about two inches from the garment. Press the burst of steam button for about 3-5 seconds. After releasing the burst of steam button you may fully lower the pressing plate.

NOTE: Do not press the burst of steam button when the pressing plate is in its lowest (closed) position.

After a few seconds, lift the handle and raise the pressing plate back to the raised position.

USING THE SPRAY BOTTLE

Lightly spray the garment before placing it on the ironing board. This helps to distribute an even, fine mist over the fabric, preparing it to be pressed, and removing all wrinkles.

USING THE PRESSING CUSHION

Some garments have been constructed with details, such as darts, curved seams and shoulder pads, which are not intended to be pressed flat. A pressing cushion is supplied with your steam press for use with these areas.

Use the cushion whenever pressing areas where no creases are desired or to shape tailored garments.

7

USK STP 20159 - 110127

Assembly page 7/24

Image 7
Contents Steam press Prensa de planchar Front cover page first Assembly page 1/24Read ALL Instructions Assembly page 2/24Special Instructions Assembly page 3/24Prong Plug Instructions Part Description Assembly page 4/24Filling the Water Tank Temperature SettingsAssembly page 5/24 Before USECotton 200C / 392F Kind of textile TemperatureSteam Control YESPressing Using the Spray BottleUsing the Pressing Cushion Assembly page 7/24Assembly page 8/24 CleaningStoring Assembly page 9/24 Safety FeaturesProblem Cause Solution Trouble ShootingAssembly page 10/24 Assembly page 11/24 WarrantyAssembly page 12/24 Kalorik Consumer Service DepartmentLEA Todas LAS Instrucciones Assembly page 13/24No intente, de ninguna manera, modificar el enchufe Assembly page 14/24Instrucciones Especiales Instrucciones Para LA Toma DE TierraPartes Assembly page 15/24USO Assembly page 16/24Antes DEL USO Para Llenar EL DepósitoUtilizar EL Vapor Assembly page 17/24Utilizar EL Cojín Assembly page 18/24Planchar Utilizar EL VaporizadorGuardar EL Aparato Assembly page 19/24Dispositivos DE Seguridad Problemas Y SolucionesProblema Causa Solución LimpiezaCalienta Assembly page 21/24Garantía Assembly page 22/24Kalorik Servicio al Consumidor Assembly page 23/24Back cover page last Assembly page 24/24