Nilfisk-ALTO 571 How to Operate the Forward / Reverse Switch see figure, Chemical manufacturer

Page 19

How To Operate the Machine

How to Operate the Forward / Reverse Switch (see figure 28).

1.To go forward, push the up arrow side of the switch.

2.To go in reverse, push the down arrow side of the switch.

How to Fill the Solution Tank

The solution tank fill port is located at the left side of the machine (see figure 29). To fill the solution tank, follow this procedure:

1.Turn the key switch to the “OFF” position.

2.Remove lid.

3.Add a cleaning chemical to the solution tank. For the correct amount of chemical, follow the directions shown on the container. NOTE: Excess foam in the recovery tank could damage the vacuum motor, so use only the minimum amount of detergent necessary.

WARNING:

Always use low foam detergent. To

 

avoid the production of foam, before

 

starting to clean, put a minimum

 

quantity of antifoam liquid into the

 

recovery tank. NEVER USE PURE

 

ACID.

4.Fill the solution tank with clean water (see figure 29).

5.After filling the solution tank, replace the solution tank lid.

WARNING:

Water solutions or cleaning materials

 

used with this type of machine can

 

leave wet areas on the floor surface.

 

These areas can cause a dangerous

 

condition for the operator or other

 

persons. Always put CAUTION signs

 

near the area you are cleaning.

WARNING:

Machines can ignite flammable

 

materials and vapors. Do not use

 

with or near flammables such as

 

gasoline, grain dust, solvents and

 

thinners. Only use a cleaning

 

concentration recommended by the

 

chemical manufacturer.

WARNING:

ALTO recommends a maximum

 

water temperature of 120°F (49°C).

Operating the Machine

NOTE: Before scrubbing with the machine, become familiar with the operations and handling of the machine. Run the machine at the lowest traverse speed. Use the machine in an area that has no furniture or objects until you can do the following:

1.Traverse the machine in a straight direction, forward and backward.

2.Stop the machine safely.

3.Turn the machine both left and right and return to a straight direction.

4.Turn a 180o turn where one rear wheel just pivots.

Figure 28

Figure 29

CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC R Manual Steering

Page -19-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operators Manual Table of Contents Operator Safety Instructions Page Introduction Introduction & Machine SpecificationsReadoperators Manualbeforeoperating Thismachine Riskoffire Symbols Used On Scrubtec RSCREEN1 Display Screens For Scrubtec RMachine Control Panel Traverse Machine Controls and FeaturesRecovery Tank Float Reverse AlarmHow to Install the Batteries How To Prepare the Machine For OperationHow To Handle the Packed Machine How to Unpack the MachineCorrect Fill Shown with Optional Chemical Mixing Sytem How To Install the Squeegee Level Indicators for the Charge of the BatteriesHow To Change or Rotate Brushes on Cylindrical Brush Head How To Remove The Brush Or Pad on the Boost machine How To Install The Brush Or Pad on the Boost machineSeat Adjustment Standard How To Operate The MachineHow to Return One Touch to Factory Default Settings How to Move the Machine Without Power see figureHow to Read the Solution Empty Indicator see , a How to Read the Battery Meter see , aHow to Read the Recovery Full Indicator see , B How to Operate the Solution Flow How to Operate the Squeegee and the Vacuum MotorHow to Operate the Brush Pressure Recovery tank. Never USE Pure How to Operate the Forward / Reverse Switch see figureHow to Fill the Solution Tank Starting to clean, put a minimumDo These Procedures When You Begin Your Work Period To traverse the machine follow this procedureHow To Operate the Machine Use gloves to protect your hands How to Clean a Very Dirty FloorDo These Procedures When You End Your Work Period Solutions when preforming the stepsRefilled with distilled water only Tap water may containContaminants that will damage Batteries. Batteries must beCleaning the Recovery Tank and Filter MaintenanceMake sure that the tank is empty first Squeegee Maintenance Cleaning the Solution Tank and FilterManually Draining the Solution Tank Vac Assisted Solution Tank DrainCleaning the Vacuum Hoses Rear Squeegee Blade ReplacementHOW to Correct Problems in the Machine Cause Action Cause Action Accessories and Options Page 71274A SectionClarketechnology Final Assembly Drawing 10/06Qty Description Rotary Cyl Boost Final Assembly Parts List 10/06Scrubtec R 571 Main Frame Assembly Drawing Rotary 9/06 Drawing#11098ADescription Qty Main Frame Assembly Parts List Rotary 5/07 Drawing#11098AClarketechnology Scrubtec R 571C Main Frame Assembly Drawing 9/06 Drawing#10949SMain Frame Assembly Parts List 9/06 Drawing#10949S Clarketechnology Scrubtec Boost R Main Frame Assembly Drawing 3/08 Drawing#11107AMain Frame Assembly Parts List 3/08 Drawing#11107A Optional Side Squeegee Lift Assembly Drawing 5/05 Optional Side Squeegee Lift Assembly Parts List 5/05 Scrubtec R 571, 586, 571 C, Boost R 1611 18, 18A Clarketechnology Clarketechnology Clarketechnology Clarketechnology Clarketechnology 3130 Steering Column Assembly Drawing 5/07 Drawing # 11087BSteering Column Assembly Parts List 5/07 Drawing # 11087B 1A, 1B, 1C 1A, 1B, 1C 2 3 4 20 19 18 17 Assembled View Cylindrical Head Assembly Drawing 5/05 Drawing#10962ACylindrical Head Assembly Parts List 3/05 Drawing#10962A Boost Head Assembly Drawing 10/06 Drawing#11103A Boost Head Assembly Drawing 6/07 Drawing#11103A Squeegee Assembly Drawing 3/08 Drawing # 10802A Ref. # Description Qty 99cm104cm Qty Optional Not supplied with machine Scrubtec R 571 Clarketechnology 6 5 Pages Electrical Connection Diagram 9/06Electrical Connection Diagram 9/06 Clarketechnology Clarketechnology Clarketechnology Clarketechnology Page Nilfisk-ALTO Division of Nilfisk-Advance A/S Norway Clarke Technology Limited U.S. Warranty
Related manuals
Manual 76 pages 18.86 Kb

BOOST R, R 571, R 586, 571 C, SCRUBTEC R 571 specifications

Nilfisk-ALTO has long been recognized for its commitment to delivering high-quality cleaning solutions, and the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 models exemplify this dedication. These compact and efficient scrubbers are designed for effective cleaning in various environments, making them suitable for both industrial and commercial applications.

The Nilfisk-ALTO 586 and SCRUBTEC R 586 models feature advanced scrubbing technology, providing users with exceptional cleaning results. They are equipped with a highly efficient brush system that can adapt to different floor surfaces, ensuring optimal cleaning performance whether in retail spaces, warehouses, or manufacturing facilities. The unique brush design simplifies the replacement process, allowing operators to switch brushes quickly and easily.

Among their key characteristics is the ability to adjust the water flow and detergent dose to suit the specific cleaning requirements. This contributes to sustainability, as it minimizes water and detergent waste while maximizing cleaning efficacy. Additionally, their ergonomic design promotes user comfort during operation, reducing fatigue during extended cleaning tasks.

The SCRUBTEC R 571 and R 571 C models bring technological advancements, including a patented electronic control system that manages all aspects of the cleaning process. This system allows users to monitor performance metrics in real-time, providing valuable insights into efficiency and usage patterns. Integrated with a large capacity solution tank, these machines can sustain longer cleaning cycles without frequent refills, making them ideal for larger areas.

Another notable feature is the ultra-compact design of these models, which facilitates maneuverability in tight spaces. Their low profile and slim design allow operators to access hard-to-reach areas, ensuring comprehensive cleaning results. Furthermore, the machines are equipped with advanced noise reduction technology, making them suitable for use in noise-sensitive environments.

Overall, the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 smoothie’s state-of-the-art features and technologies offer exceptional cleaning efficiency. Their operational flexibility, coupled with user-friendly controls, positions them as an ideal choice for businesses looking to invest in reliable and effective floor cleaning solutions. With Nilfisk-ALTO, users can count on superior performance and durability built into every model.
Top Page Image Contents