Nilfisk-ALTO R 571 C, SCRUBTEC R 586 HOW to Correct Problems in the Machine Cause Action

Page 27

HOW TO CORRECT PROBLEMS IN THE MACHINE

PROBLEM

CAUSE

ACTION

 

 

 

 

Insufficient water onto the brushes

The solution flow is not set

Make sure the solution flow is set.

 

There is no water in the solution tank.

Fill the solution tank.

 

The solution filter is dirty.

Clean the solution filter.

 

A circuit breaker has tripped.

Reset the circuit breaker.

 

Insufficient flow.

Increase flow with solution switch.

 

 

 

 

The machine does not clean

The brushes are worn.

Check the brushes and replace if necessary.

satisfactorily

 

(the brushes have to be replaced when the

 

 

bristles reach approximately .59 inches (15mm

 

 

height.)

 

Need to use a different kind of brush/pad

Use a different kind of brush. For cleaning

 

 

operations on floors where the dirt proves to be

 

 

particularly resistant, we recommend using spe-

 

 

cial brushes. See Accessories page.

 

 

 

 

The squeegee does not dry the floor

The squeegee is dirty.

Clean the squeegee.

 

Recovery drain hose is not closed.

Close the drain plug.

 

The suction hoses need to be cleaned.

Clean the vacuum hoses. See “Routine Main-

 

 

tenance” section.

 

The squeegee blades are worn.

Replace/ or rotate the squeegee blades. See

 

 

“Routine Maintenance” section.

 

The recovery tank is full.

Drain recovery tank.

 

 

 

 

The vacuum motor does not function

The squeegee up/down switch in not in the

Put the squeegee in the low or middle position

 

low or middle position.

or reprogram “one touch”.

 

 

 

 

The machine does not start

The operator is not properly seated.

The operator must be properly seated in the

 

 

driving position.

 

The key is not in the “ON position”.

Turn the key to the “ON” position.

 

The charger is still connected.

Remove the A/C cord from the wall.

 

The batteries are not charged or not con-

Check to make sure the batteries are con-

 

nected properly.

nected properly and charge if necessary.

 

The circuit breaker has tripped.

Reset the circuit breaker.

 

 

 

 

The brush motors do not work

The brush head unit is not down.

Put the brush head unit down.

WARNING: To avoid damage to the

The batteries are not charged or not con-

Check to make sure the batteries are con-

floor, the motor starts only when the

machine is traversing.

nected properly.

nected properly and charge if necessary.

 

Poor electrical connection at the brush head

Connect the electrical connection at the brush

 

unit.

head unit.

 

 

 

 

CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC R Manual Steering

Page -27-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operators Manual Table of Contents Operator Safety Instructions Page Introduction Introduction & Machine SpecificationsReadoperators Manualbeforeoperating Thismachine Riskoffire Symbols Used On Scrubtec RSCREEN1 Display Screens For Scrubtec RMachine Control Panel Traverse Machine Controls and FeaturesRecovery Tank Float Reverse AlarmHow to Install the Batteries How To Prepare the Machine For OperationHow To Handle the Packed Machine How to Unpack the MachineCorrect Fill Shown with Optional Chemical Mixing Sytem How To Install the Squeegee Level Indicators for the Charge of the BatteriesHow To Change or Rotate Brushes on Cylindrical Brush Head How To Remove The Brush Or Pad on the Boost machine How To Install The Brush Or Pad on the Boost machineSeat Adjustment Standard How To Operate The MachineHow to Return One Touch to Factory Default Settings How to Move the Machine Without Power see figureHow to Read the Battery Meter see , a How to Read the Solution Empty Indicator see , aHow to Read the Recovery Full Indicator see , B How to Operate the Squeegee and the Vacuum Motor How to Operate the Solution FlowHow to Operate the Brush Pressure Recovery tank. Never USE Pure How to Operate the Forward / Reverse Switch see figureHow to Fill the Solution Tank Starting to clean, put a minimumDo These Procedures When You Begin Your Work Period To traverse the machine follow this procedureHow To Operate the Machine Use gloves to protect your hands How to Clean a Very Dirty FloorDo These Procedures When You End Your Work Period Solutions when preforming the stepsRefilled with distilled water only Tap water may containContaminants that will damage Batteries. Batteries must beMaintenance Cleaning the Recovery Tank and FilterMake sure that the tank is empty first Squeegee Maintenance Cleaning the Solution Tank and FilterManually Draining the Solution Tank Vac Assisted Solution Tank DrainCleaning the Vacuum Hoses Rear Squeegee Blade ReplacementHOW to Correct Problems in the Machine Cause Action Cause Action Accessories and Options Page 71274A SectionClarketechnology Final Assembly Drawing 10/06Qty Description Rotary Cyl Boost Final Assembly Parts List 10/06Scrubtec R 571 Main Frame Assembly Drawing Rotary 9/06 Drawing#11098ADescription Qty Main Frame Assembly Parts List Rotary 5/07 Drawing#11098AClarketechnology Scrubtec R 571C Main Frame Assembly Drawing 9/06 Drawing#10949SMain Frame Assembly Parts List 9/06 Drawing#10949S Clarketechnology Scrubtec Boost R Main Frame Assembly Drawing 3/08 Drawing#11107AMain Frame Assembly Parts List 3/08 Drawing#11107A Optional Side Squeegee Lift Assembly Drawing 5/05 Optional Side Squeegee Lift Assembly Parts List 5/05 Scrubtec R 571, 586, 571 C, Boost R 1611 18, 18A Clarketechnology Clarketechnology Clarketechnology Clarketechnology Clarketechnology 3130 Steering Column Assembly Drawing 5/07 Drawing # 11087BSteering Column Assembly Parts List 5/07 Drawing # 11087B 1A, 1B, 1C 1A, 1B, 1C 2 3 4 20 19 18 17 Assembled View Cylindrical Head Assembly Drawing 5/05 Drawing#10962ACylindrical Head Assembly Parts List 3/05 Drawing#10962A Boost Head Assembly Drawing 10/06 Drawing#11103A Boost Head Assembly Drawing 6/07 Drawing#11103A Squeegee Assembly Drawing 3/08 Drawing # 10802A 99cm Ref. # Description Qty104cm Qty Optional Not supplied with machine Scrubtec R 571 Clarketechnology 6 5 Pages Electrical Connection Diagram 9/06Electrical Connection Diagram 9/06 Clarketechnology Clarketechnology Clarketechnology Clarketechnology Page Nilfisk-ALTO Division of Nilfisk-Advance A/S Norway Clarke Technology Limited U.S. Warranty
Related manuals
Manual 76 pages 18.86 Kb

BOOST R, R 571, R 586, 571 C, SCRUBTEC R 571 specifications

Nilfisk-ALTO has long been recognized for its commitment to delivering high-quality cleaning solutions, and the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 models exemplify this dedication. These compact and efficient scrubbers are designed for effective cleaning in various environments, making them suitable for both industrial and commercial applications.

The Nilfisk-ALTO 586 and SCRUBTEC R 586 models feature advanced scrubbing technology, providing users with exceptional cleaning results. They are equipped with a highly efficient brush system that can adapt to different floor surfaces, ensuring optimal cleaning performance whether in retail spaces, warehouses, or manufacturing facilities. The unique brush design simplifies the replacement process, allowing operators to switch brushes quickly and easily.

Among their key characteristics is the ability to adjust the water flow and detergent dose to suit the specific cleaning requirements. This contributes to sustainability, as it minimizes water and detergent waste while maximizing cleaning efficacy. Additionally, their ergonomic design promotes user comfort during operation, reducing fatigue during extended cleaning tasks.

The SCRUBTEC R 571 and R 571 C models bring technological advancements, including a patented electronic control system that manages all aspects of the cleaning process. This system allows users to monitor performance metrics in real-time, providing valuable insights into efficiency and usage patterns. Integrated with a large capacity solution tank, these machines can sustain longer cleaning cycles without frequent refills, making them ideal for larger areas.

Another notable feature is the ultra-compact design of these models, which facilitates maneuverability in tight spaces. Their low profile and slim design allow operators to access hard-to-reach areas, ensuring comprehensive cleaning results. Furthermore, the machines are equipped with advanced noise reduction technology, making them suitable for use in noise-sensitive environments.

Overall, the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 smoothie’s state-of-the-art features and technologies offer exceptional cleaning efficiency. Their operational flexibility, coupled with user-friendly controls, positions them as an ideal choice for businesses looking to invest in reliable and effective floor cleaning solutions. With Nilfisk-ALTO, users can count on superior performance and durability built into every model.
Top Page Image Contents