John Lewis JLBIWD 1400 Water inlet, Appliance must be connected to a cold water supply

Page 10

Position the base into the recess with its front edge as far forward as the adjoining plinth line will allow.

The reason for placing the base in this position is to allow a small strip of beading to be fitted in front of the appliance feet.

Fix the base firmly to the floor using four appropriate countersunk screws (see Fig. H).

Hardwood strip

5 X 25 X 605

5 mm x 25 mm

490

 

600-605

H

With the appliance installed adjust all four feet ensuring the machine is stable, and a clearance of approximately 5 mm is left between the top of the machine and the underside of the worktop.

A final check for stability should be carried out with the machine on spin with a load, this will identify the need for any further fine adjustment to the feet.

A strip of beading approximately 605 mm W, x 5 mm H, x 25 mm D must be screwed down into the base directly in front of the machine’s feet, this will provide additional security.

If required an additional door magnet, part number 1242394-00/3 and disc, part number 1242393-00/5 are available from spare parts.

Water inlet

Connect the hose to a tap with a 3/4” thread. Always use the hose supplied with the appliance to connect to the water supply.

Do not use previously used hoses for water connection.

The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window “A”. Should this occur, turn the water tap off and refer to your Service Centre to replace the hose.

A

P0352

Installation should comply with local water authority and building regulations’ requirements.

The appliance must be connected to a cold water supply.

A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance.

If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system.

There should be a minimum distance of 5.02m

(16.5 ft) between the appliance’s inlet and the bottom of the water storage tank.

Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.

P0021

10

Image 10
Contents Jlbiwd Maintenance and Cleaning InstallationChild Safety ServiceContents Ecological hints Materials marked with the symbol are recyclableYour New Washer-Dryer Environmental InformationDetergent dispenser drawer Child safety featureDescription of the Appliance Prewash Main wash Fabric softenerWashing Installation InstructionsTechnical Specifications DryingUnpacking Installation on a Suspended FloorQualified plumber Door Preparation and assembly of the doorBuilding-in HingesCounter-magnet Mounting the doorDrill four fixing holes see Fig. G Water inlet Appliance must be connected to a cold water supplyInto a drainage standpipe Water drainageOnto a sink outlet spigot Interest of the environment LevellingSpecial conditions Electrical connectionBlue- Neutral Brown- Live Permanent connectionWith the current electrical regulations On/Off button Control PanelDetergent dispenser drawer Mains-on light Spin buttonTime dry button Delay start buttonAutomatic Dry button Start/Pause buttonSelection of drying time in minutes ExampleProgramme phase indicator lights Programme selector dialProgramme information Easy ironLoad the laundry Switch the machine onOperating Sequence Measure out the detergentSelect the spin speed or the Rinse hold option Select the Delay startHow to change an option or a programme during its cycle Select the desired optionsLevel of the water is not high Drum is not turning How to interrupt a programmeEnd of programme Draining only or Draining and spin onDrying Press the Start/Pause button to start the programme900 r.p.m. for Cottons & Synthetics with electronic drying Sheet Washing and Drying Hints1000g = 1 kg Bath robeWash Care Symbols Important NotesWashing programmes Energy Water Time Description KWh Off ResetProgramme Consumptions SoakDrying Programmes Degree Type of fabric Max. load Spin speed Drying time MinsMaintenance and Cleaning Cleaning the water inlet filter Emergency emptying outSomething Not Working Spinning Unsatisfactory washing resultsMachine vibrates when Door will not open0870 01 132 984

JLBIWD 1400 specifications

The John Lewis JLBIWD 1400 is a highly efficient and versatile washing machine that meets the demands of modern households. This integrated washer dryer combines practicality with advanced technology, making it a popular choice among consumers seeking a reliable laundry solution.

One of the standout features of the JLBIWD 1400 is its impressive capacity. With a washing load of up to 8 kg and a drying load of 5 kg, this machine is designed to handle large volumes of laundry, making it suitable for families or those with busy lifestyles. Its 1400rpm spin speed ensures that clothes come out damp but not soaking wet, reducing drying time significantly.

The JLBIWD 1400 incorporates a variety of washing programs tailored for different fabric types and user preferences. From gentle cycles for delicate items to powerful settings for heavily soiled clothing, the machine offers flexibility to cater to individual needs. The quick wash option is an added convenience, allowing users to clean small loads in as little as 15 minutes.

Another key characteristic of the John Lewis JLBIWD 1400 is its energy efficiency. With an energy rating of A, this washer dryer helps reduce electricity bills while minimizing environmental impact. The machine is designed to use water and energy judiciously without compromising performance.

In terms of technology, the JLBIWD 1400 is equipped with an intuitive control panel that allows users to select programs easily. The digital display provides clear feedback on the selected washing cycle and remaining time, enhancing usability. Additionally, the delay start feature offers the convenience of scheduling laundry for a more suitable time, such as during off-peak energy hours.

Safety features are also paramount, and this model includes a child lock function to prevent accidental operation. The machine is built with robust materials designed for longevity and comes with a warranty, providing peace of mind to consumers.

The John Lewis JLBIWD 1400 combines features, technology, and efficiency in one sleek package. With its large capacity, diverse washing programs, and user-friendly interface, it stands out as a reliable appliance that simplifies the laundry process for households everywhere.