GE Monogram ZBD6605 owner manual Control Panel/Operation ZBD6905, Normal, High, Sani

Start a wash load

Control Panel/Operation – ZBD6905

Chef’s Washer

3.SMART DRY–When selected, sensors detect the presence of rinse aid and the final rinse temperature. The drying heater and fan are then turned on for the minimum time to achieve optimum drying results, saving energy over conventional heated dry and time over non-heated dry. SMART DRY is not available on RINSE ONLY.

4.WATER TEMP–This button provides extra heat options to increase water temperature for optimum performance.

NORMAL							This is the default setting–provides a wash and rinse with water temperatures
							up to 125°F (51°C) in the LIGHT WASH, 135°F (57°C) in the NORMAL
							WASH cycle and 155°F (68°C) in HEAVY DUTY.
HIGH							This water temp selection provides a wash and rinse with water temperatures
							up to 160°F (71°C) in LIGHT WASH, NORMAL WASH and HEAVY DUTY.
							Use this option for heavily soiled dishes. Cannot be used with RINSE ONLY.
SANI							This water temp selection provides a sanitizing wash and rinse with water
							temperatures up to 160°F (71°C) in LIGHT WASH and 171°F (77°C) in
							NORMAL WASH and HEAVY DUTY. Cannot be used with RINSE ONLY.
							At the end of the WASH cycle, the SANI OPTION light will remain illuminated
							to indicate that the sanitization conditions have been met.
			ID	E	N T	I	NSF INTERNATIONAL
		S
	E
						A	Meets NSF Protocol for Performance of Domestic Spray-Type Pots
R						L
							and Pans Washing Machines (NSF Protocol P180) Requirements for
							cleaning and sanitization of cookware.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

5.DELAY START–This option will allow you to delay the start time of any wash cycle except RINSE ONLY for up to 6 hours.

1.Select the delay start time you want by pressing the DELAY START button. Multiple pressing will alternate the delay time between 2, 4 or 6 hours and OFF.

2.The last programmed cycle will automatically be selected. A new cycle and options can also be selected. The DELAY START light/lights will flash to indicate time selected.

3.The flashing Delay Start Indicators show how many hours will elapse before washing begins.

To start the Chef’s Washer, close the door until it locks in place. The last used cycle will be displayed. To begin this cycle, push the START button. To select a different cycle, push the desired Cycle Selection and Option buttons, and then press the START button.

The door must be closed and latched into place to select a cycle or an option.
To interrupt/pause a cycle, press the selected cycle button. The Status Indicators will flash.
CAUTION: Be careful when opening the door; the hot steam that escapes when the door is
opened may cause injuries. Stand back as you open the door and allow the steam
to escape.
ATTENTION : Faites attention lorsque vous ouvrez la porte. La vapeur brûlante qui s’échappe
lorsque vous ouvrez la porte pendant un programme de lavage peut causer des
brûlures. Lorsque vous ouvrez la porte, reculez et laissez la vapeur s’échapper
de l’appareil.
To restart the wash process, close the door until it locks in place. Re-press the cycle button. There
may be a time delay of up to a few minutes, because the temperature inside the Chef’s Washer
needs to stabilize before it restarts the wash cycle. During this time the SENSING light will be on.
To cancel the cycle after it has started, press and hold the START/CANCEL button for 3 seconds.
The Chef’s Washer will then drain and the cycle indicator lights will flash. At this point a new wash
cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out after the
Chef’s Washer drains. If you have selected a new wash cycle, remember to add more detergent to
the detergent compartment if required.	11