John Lewis JLWM 1406 Unpacking, Positioning, Installation on a suspended floor, Plumbing

Page 23

Unpacking

All transit bolts and packing must be removed before using the appliance.

Keep all packaging away from children.

You are advised to keep all the transit bolts for re-use in case the machine is to be transported again.

After removing all the packaging, with assistance carefully lay machine on it’s back to remove the polystyrene base from the bottom.

Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance.

HEC0008

HEC0001

With the spanner provided unscrew and remove the central rear bolt A.

Unscrew and remove the two large rear bolts B and the six smaller bolts C.

HEC0010

HEC0005

 

Connect the water inlet hose as described under the paragraph “Water inlet”.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units.

Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

If the floor is carpeted or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine.

A

HEC00022

 

 

C

 

 

B

HEC0003S

C

B

Warning

The machine should NOT be placed on deep pile carpeting.

Installation on a suspended floor

Suspended wooden floors are particularly susceptible

Remove the bracket D, refit the six smaller bolts C and slide out the relevant plastic spacer E.

to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor

D

HEC0011S

E

C

HEC0023 C

boards with screws. If possible install the appliance in one of the corners of the room, where the floor is more stable.

Note

Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.

Open the porthole and remove the polystyrene block fitted on the door seal.

Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet.

Plumbing In

Your new washing machine has been designed to be permanently plumbed in to your home’s water supply and drainage system. However, if this is not possible, it may be connected to a suitable existing tap with the drain hose discharging into a sink.

The appliance has an inlet hose, with female 3/4” BSP

23

Image 23
Contents Jlwm Spin washing machine Use InstallationChild safety Environmental information Maintenance and cleaning ServiceMaterials marked with the symbol are recyclable Ecological hintsContents Detergent dispenser drawer On/Off and Reset buttonTemperature button Door Lock pilot light Spin speed button Control panelExtra rinse option Spin speed indicator «Rinse hold» and «QUIET» optionsDisplay and buttons Multi-Display«Programme selector» buttons Acoustic Signal«On/Off» / «Reset» programme button «Temperature» button«Quick» button «Spin» button«Options» button «Extra rinse» buttonDoor Lock pilot light «Delay start» button«Start/pause» button Load the laundry Switch the machine on and select the desired programmeSelect the desired temperature and spin speed Select the Delay start optionProgramme correction Cancel a programme or switch the appliance offHow to interrupt a programme End of programmeBath robe Hints & tips on washing1000g = 1 kg SheetImportant notes Wash care symbolsWashing programmes Water draining Programme descriptionLoad Lingerie, underwearFreshening up Main wash rinses Spin at ItemsCan be used for laundry which is Lightly soiled or which needsMaintenance and cleaning Screw the pump cover fully Close the pump door Cleaning the water inlet filterEmergency emptying out Remove any objects from the pump impeller by rotating itSomething not working Door will not open Green Start/Pause lightMachine vibrates when SpinningPrewash Main wash Fabric softener Child safety featureDescription of the appliance Detergent dispenser drawer«COTTONS ECONOMY» at 60C InstallationTechnical specifications Plumbing Installation on a suspended floorUnpacking PositioningInto a drainage standpipe Water inletWater drainage Appliance must be connected to a cold water supplyOnto a sink outlet spigot LevellingInterest of the environment Electrical connection Permanent connection Repairs After sales service34/08 132 961