Whirlpool Front-Load Washer manual Installation Instructions, Remove Transport System

Page 7

INSTALLATION

INSTRUCTIONS

Remove Transport System

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the unit is within approximately 3 ft (90 cm) of the final location.

There are 4 bolts in the rear panel of the washer that support the suspension system during transportation.

HOTCOLD

1.Using a ½ in. (13 mm) wrench, loosen each of the bolts.

2.Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt and the cable attached to the bolt. The power cord will be attached to all 4 bolts.

3.Once all 4 bolts are removed, remove the power cord from each bolt holder, and discard bolts, plastic spacers, and cables.

4.Close the holes with the transport bolt hole plugs.

Connect the Inlet Hoses

Connect the inlet hoses to the water faucets

Make sure the washer drum is empty.

1.Attach the hose with the red color indicator to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

2.Attach the hose with the blue color indicator to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

3.Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

4.Turn on the water faucets and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

Route the Drain Hose

Proper routing of the drain hose protects your floors from damage due to water leakage. Carefully read and follow these instructions.

The drain hose is connected to your washer.

To prevent drain water from going back into the washer:

■Do not straighten the drain hose, and do not force excess drain hose into standpipe. Hose should be secure, but loose enough to provide a gap for air.

■Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. (See Floor Drain under “Alternate Parts You May Need.”)

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Use & Care Guide Table of Contents/Table des matièresFRONT-LOADING Laveuse Automatique ÀTable of Contents Your safety and the safety of others are very important Washer SafetyAlternate Parts You May Need Installation RequirementsTools and Parts Optional PedestalLaundry tub drain system view Washer DimensionsRecessed area or closet installation Drain SystemGrounding Instructions Electrical RequirementsRoute the Drain Hose Installation InstructionsRemove Transport System Connect the Inlet HosesSecure the Drain Hose Complete InstallationLevel the Washer Smart Dispensers Accuwash Automatic Temperature ControlCatalyst Cleaning Action with Direct Injection Electronic ControlsTo load washer Washer USEStarting Your Washer First Wash Cycle Without LaundryTo fill dispenser compartments Using the DispenserChoosing the Right Detergent Detergent compartmentStatus Lights Pausing or RestartingCycles Modifiers OptionsLaundry Guide Laundry TipsLoading Vacation, Storage, and Moving Care Cleaning Your WasherWasher Care Water Inlet HosesTroubleshooting Did you overload the washer? Are you using a low speed wash cycle?Was the wash temperature too low? Did you sort properly?Canada If you need replacement partsFor service in Canada U.S.AWhirlpool Corporation will not pay for Whirlpool Washer WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA LaveuseOutils et pièces Exigences ’INSTALLATIONExigences d’emplacement Outils nécessaires pour l’installationSystème de vidange Avertissement Installation électriqueAcheminement du tuyau de vidange Instructions ’INSTALLATIONEnlèvement du système de transport Raccordement des tuyaux d’alimentationImmobilisation du tuyau de vidange Achever l’installationRéglage de l’aplomb de la laveuse Caractéristiques ET Avantages Pour charger la laveuse Utilisation DE LA LaveuseMise en marche de la laveuse Premier programme de lavage sans linge à laverPour commencer immédiatement le programme de Utilisation du distributeurChoix du détergent approprié Compartiment du détergentCompartiment d’eau de Javel Pause ou remise en marcheChangement de programmes, options et Modificateurs Compartiment d’assouplissant de tissuProgrammes Témoins lumineuxRéglages préréglés des programmes Soak TrempageRinse/Spin Rinçage/essorage Drain/Spin Vidange/essorageGuide de température Extra Rinse Rinçage supplémentaireRinse Hold Rinçage/attente Wash/Rinse Temp Température de lavage/rinçageGuide de lessivage Conseils DE LessivageChargement Nettoyage de la laveuse Entretien DE LA LaveuseDépannage Avez-vous bien trié la charge? Avez vous effectué le tri correctement?Avez-vous surchargé la laveuse? Avez-vous utilisé suffisamment de détergent?Si vous avez besoin de pièces de rechange Pour le service au CanadaAux États-Unis Au CanadaWhirlpool Corporation ne paiera pas pour Garantie DE LA Sécheuse WhirlpoolWhirlpool Corporation All rights reserved 4619 7020

Front-Load Washer specifications

Whirlpool has established itself as a leader in home appliances, and its Front-Load Washer is a standout model that embodies innovation and efficiency. Designed to meet the needs of modern households, this washer features a sleek, space-saving design that not only enhances your laundry room but also provides ample capacity for family-sized loads.

One of the main features of the Whirlpool Front-Load Washer is its advanced washing technology. Equipped with Adaptive Wash Technology, the washer automatically adjusts the cycle settings based on the size of the load and the amount of soil in the clothes. This ensures optimal cleaning performance while conserving water and energy, making it an environmentally-friendly choice.

Energy efficiency is further enhanced with the Energy Star certification, which signifies that the washer meets stringent energy-saving guidelines. Users can save on utility bills while also contributing to a sustaining environment. The washer uses less water and energy per load compared to traditional top-load models, allowing for impressive cleaning without excess waste.

The precision cleaning system is another key characteristic of the Whirlpool Front-Load Washer. This feature combines several technologies to ensure that dirt and stains are effectively eliminated. The efficient wash action and specialized wash motions work together to provide a thorough clean, while the sensitive drying technology gently tumbles clothes to prevent overdrying, preserving fabric quality.

Moreover, the washer offers a variety of wash cycles to accommodate different fabrics and cleaning needs. From delicate cycles for gentle fabrics to heavy-duty options for sturdy items like towels and bed linens, users can select the most suitable settings for their laundry.

Additional features include a smooth, durable drum that is designed to be gentle on clothes, as well as a delay start option that allows you to schedule washes at your convenience. The user-friendly control panel with intuitive buttons and a digital display makes selecting the right cycle a breeze.

Overall, the Whirlpool Front-Load Washer combines innovative technology with intuitive design, making it a top choice for households looking for efficiency, performance, and ease of use in their laundry routines. Whether you're washing a small load of delicates or tackling a large pile of family laundry, this washer is equipped to handle it all with precision.
Top Page Image Contents