Blomberg WNF9422SC20 Installation, Connecting water supply, Appropriate installation location

2	Installation	3.	Attach the plastic covers supplied in the
Refer to the nearest Authorised Service Agent			User Manual bag into the holes on the rear
			panel. (P)
for installation of the product. To make the
product ready for use, review the information
in the user manual and make sure that the
electricity, tap water supply and water drainage
systems are appropriate before calling the		C	Keep the transportation safety bolts in
Authorized Service Agent. If they are not, call			a safe place to reuse when the washing
a qualified technician and plumber to have any			machine needs to be moved again in the
necessary arrangements carried out.			future.
C	Preparation of the location and electrical,	C	Never move the product without the
	tap water and waste water installations at		transportation safety bolts properly fixed in
	the place of installation is under customer's		place!
	responsibility.	Connecting water supply
B Installation and electrical connections of		C The water supply pressure required to run
	the product must be carried out by the
			the product is between 1 to 10 bars (0.1
	Authorized Service Agent. Manufacturer
			– 10 MPa). It is necessary to have 10 – 80
	shall not be held liable for damages that
			liters of water flowing from the fully open
	may arise from procedures carried out by
			tap in one minute to have your machine run
	unauthorized persons.
			smoothly. Attach a pressure reducing valve
A Prior to installation, visually check if the
			if water pressure is higher.
	product has any defects on it. If so, do not
		C If you are going to use the double water-
	have it installed. Damaged products cause		inlet product as a single (cold) water-inlet
	risks for your safety.
			unit, you must install the supplied stopper
C Make sure that the water inlet and
			to the hot water valve before operating the
	discharge hoses as well as the power
			product. (Applies for the products supplied
	cable are not folded, pinched or crushed
			with a blind stopper group.)
	while pushing the product into its place
		C If you want to use both water inlets of the
	after installation or cleaning procedures.
			product, connect the hot water hose after
Appropriate installation location
			removing the stopper and gasket group
•	Place the machine on a rigid floor. Do
			from the hot water valve. (Applies for the
	not place it on a long pile rug or similar		products supplied with a blind stopper
	surfaces.		group.)
•	Total weight of the washing machine and	A Models with a single water inlet should not
	the dryer -with full load- when they are		be connected to the hot water tap. In such
	placed on top of each other reaches to		a case the laundry will get damaged or the
	approx. 180 kilograms. Place the product		product will switch to protection mode and
	on a solid and flat floor that has sufficient		will not operate.
	load carrying capacity!	A Do not use old or used water inlet hoses
•	Do not place the product on the power		on the new product. It may cause stains on
	cable.		your laundry.
•	Do not install the product at places where	1.	Connect the special hoses supplied with
	temperature may fall below 0ºC.		the product to the water inlets on the
•	Place the product at least 1 cm away from		product. Red hose (left) (max. 90 ºC) is for
	the edges of other furniture.		hot water inlet, blue hose (right) (max. 25
Removing packaging reinforcement			ºC) is for cold water inlet.

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

Removing the transportation locks

ADo not remove the transportation locks before taking out the packaging

reinforcement.

A Remove the transportation safety bolts before operating the washing machine, otherwise, the product will be damaged.

1. Loosen all the bolts with a spanner until they rotate freely (C).

2.Remove transportation safety bolts by turning them gently.

3 - EN