Maytag MAF 9801 manual Wash motor fault. Phone Service, Wrong Language on the Display

Page 29

Over flow. Phone Service.

Temperature stop fault. Faulty temperature stop, phone Service.

Thermistor fault. Faulty thermistor, phone Ser- vice.

Water inlet fault. Fault in the supply of water, ensure:

-that the water tap is open.

-that the strainer in the water inlet connection is not clogged.

1. Turn off the water tap.

2. Disconnect the hose.

3. Clean the strainer in the water inlet of the machine.

4. Re-connect the hose.

5. Open the water tap.

6. Run the programme again to check that the fault is remedied.

Water outlet fault. Faulty pumping, check the drain hose and the drain pump.

1. Straighten out any kinks in the drain hose.

2. Is there anything stuck in the drain hose outlet? Clear the hose.

3. Is the drain pump blocked by foreign ob jects? Clear the pump, see Chapter 12, Care and cleaning.

4. Run the programme Drain.

Wash motor fault. Phone Service.

0000 flashes at the top right of the display. The machine has failed to spin.

1. The machine incorporates an out-of-balance detector, which reduces spin speed or prevents spinning from starting if the load is very unba-

lanced. Turn the main switch, off and turn it on again. Open the door and redistribute the washing.

2. After correcting, run the programme Spin.

If flashes at the lower right corner of the display it is an indication that you have attemp- ted to start a programme with the door open. Close the door and try again.

WRONG LANGUAGE ON THE DISPLAY

If the language on the display becomes altered for any reason, it can be restored to the initial language again.

The available languages are Dansk, Deutsch, English, Espanol, Français, Italiano, Nederlands, Norsk, Portugués, Suomi and Svenska.

Proceed as follows to change the language:

Turn the main switch, off and turn it on again. Press the Enter button five times, then press the P1 button five times. These ten ti- mes must be completed within fifteen seconds.

Within three seconds after pressing P1 the last time, step to the desired language using the

buttons.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Maytag Contents Transport Supports Before Washing the First TimeWasher Door Check Hardness of the WaterGeneral Safety InstructionsOverfill Protection Interrupting a ProgrammeDisposal TRANSPORT/ Winter StorageProtect Children Childrens SafetyCHILD-SAFE Washing Detergent Compartment Parts of the Washing MachineLC-DISPLAY PanelBefore Washing Avoid Creases Washing High Water LevelMinimizing Allergy Hazards Save TimeWashing Time DetergentsTextile Dyeing Washing with Easy Control Washing4PUTTING in the Washing and DETER- Gent 1SORT the Washing3O P E N T H E D O O R a N D P U T I N T H E Washing 6TEMPORARY Alteration of TEMPERA- Ture and Spin Speed ButtonDuring the Programme Programme with the Button8PROGRAMME Completed 9WHEN Washing is FinishedTemporary Spinning or Rinsing Delayed Start 1-24 HoursConsumption Values PRE-SET Programmes Making OWN Washing Programmes Available Settings and Options Interrupt Input Create Your OWN Washing ProgrammeTIP Reset Programme Available Types of Programme PreSelect High water level Menu System for Changing a Preset ProgrammeThis page has been left blank for technical printing reasons Cleaning the Outside of the Machine Care and CleaningCleaning the Detergent Compartment Hard Water Cleaning Holes Under the RidgesFault Indications Trouble ShootingDoor will not Open Machine will not StartWrong Language on the Display Wash motor fault. Phone ServiceCelsius or Fahrenheit TernativeStandard Tests Technical DataTechnical Information This page has been left blank for technical printing reasons Guarantee Service and GuaranteeService Washing Quick GuideChapter Index
Top Page Image Contents