Frigidaire 137058000A 0808, GLGQ2152EE manual Dryer Tech Data Sheet, Reading Error Codes

Dryer Tech Data Sheet

This information is intended for Qualified Technicians Only.

CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE SERVICING

Please Return This Sheet to its Envelope in the Product for Future Reference

READING ERROR CODES

1.Non-Digital Readout Display Models: Rotate cycle selector knob to the 3 O’clock position.

Digital Readout Display Models: Rotate cycle selector knob clockwise (3) settings from the Normal cycle option.

2.Press and hold the Select and Pause Cancel buttons simultaneously for six seconds.

3.Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds.

4.Digital Readout Display Models: rotate the timer knob (1) click counterclockwise. The error code will appear in the digital display.

Non-Digital Readout Display Models: rotate the cycle selector knob to the 2 O’clock position. The four indicator lights of Drying, Cool Down, Wrinkle Rid (Press Saver), and Clean Lint Filter will flash the number of times for the first digit of the code and the START indicator light will flash the number of times for the second digit. Take separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting the number of times the lights flash. Example E24: The four indicator lights would flash twice indicating the 2 and the START indicator light will flash four times indicating the 4. The four indicator lights and the START indicator light start flashing at the same time. The control will pause for 2 seconds, then repeat the code.

NOTE: A letter appearing in the code stands for a number higher than nine. A = 10 B = 11 C = 12 D = 13 E = 14 F = 15

Example Code E4A: the first digit would be 4 and the second digit would be 10. If this code would appear on a washer in the Non-Digital Readout Display Models, the four indicator lights would blink four times and the START indicator light would blink ten times. Troubleshoot the problem by using the chart below.

To move on to the next code, press the OPTIONS button.

To clear code, press the Select button. Code will be cleared when mode is exited.

To exit this mode, simultaneously press and hold the Select and Pause Cancel buttons for six seconds.

Error Code	Label	Description	Solution
E10	General EEPROM	Problem with communication	Clear code, exit mode and start dryer. If problem persists, replace electronic
	Fault	between EEPROM and the	control.
		microprocessor.
E11	Checksum Error	Problem with communications or	Clear code, exit mode and start dryer. If problem persists, replace electronic
		memory did not check, one has	control.
		become corrupted.
E12	Non fatal R/W	Problem reading or writing to the	Clear code, exit mode and start dryer. If problem persists, replace electronic
	error	memory or input/output.	control.
E24	Control NTC Short	Control thermistor or its wiring is	Remove wires from control thermistor. Measure resistance of thermistor. If
	Circuit	shorted.	reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (±
			10%), check wiring between thermistor and electronic control. If good,
			replace electronic control.
E25	Control NTC Open	Control thermistor or its wiring is	Remove wires from control thermistor. Measure resistance of thermistor. If
	Circuit	open.	reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (±
			10%), check wiring between thermistor and electronic control. If good,
			replace electronic control.
E4A	Program Timeout	The drying time has exceeded	Press Pause Cancel and SELECT buttons for 6 seconds to exit test modes.
	Fault	program time for that cycle.	Position cycle selector to NORMAL, temperature selector to HIGH HEAT
			and touch START. Check for anything that would extend dry times such as:
			no heat, restricted vent, blower fan blade broken or loose, dryer installed in
			closet with solid door, or bad connection in moisture sensor bar circuit or
			dirty bars. If dryer operates normally but code returns, replace electronic
			control.
E5B	Heater Fault (no	Temperature reading of control	Position cycle selector to NORMAL, temperature selector to HIGH HEAT
	heating)	thermistor has not changed in a	and touch START. Measure voltage across terminals on relay K2 (heater
		certain amount of time.	relay) on electronic control. If meter reads 240V on electric models and
			120V on gas models, replace electronic control. If meter reads zero, remove
			power from dryer. Disconnect wire going to NO terminal on the relay K2.
			Reconnect power and measure voltage drop between terminal COM on
			relay K2 and neutral. If meter reads zero, wire between incoming line and
			relay K2 is open. If meter reads 120V, check the rest of the heater circuit.
E68	Key (button) Struck	One of the keys (buttons) is stuck	Enter function test mode and perform key (button) test to determine which
	Fault	closed (active).	button is at fault. Carefully free the and perform the test again. If button is
			free but the key struck code still exists, replace electronic control.
E8C	Too many trips in a	The safety (high limit) thermostat	Check for blocked lint filter, blocked exhaust, air leaks around air duct,
	period of time.	has tripped too many times within	broken blower fan blades, worn or loose drum seals, dryer installed in closet
		a certain period of program time.	with solid doors or door seal not correctly seated.
EAF	Watch Dog Reset	Microcontroller has been reset by	Clear code, exit mode and start dryer. If problem persists, replace electronic
		internal Watchdog timer.	control.

137058000A 0808