Blomberg DV 17540 NBL00 Installation Instructions Awarning Risk of fire, Electrical connection

Page 8

3Installation Instructions

AWARNING - Risk of fire

•The clothes dryer (“appliance‘) installation must be performed by a qualified installer. •Install the appliance according to the manufacturer’s instructions and local codes. •Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the ap pliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct the clothes dryer’s airflow and increase the risk of fire.

To reduce the risk of severe injury or death, follow all installation instructions.

SAVE THESE INSTRUCTIONS

Electrical connection

Connect the appliance to a grounded outlet protected by a fuse or circuit breaker of suitable capacity.

Dryer shipped with cord to fit this type 4 -wire receptacle

4-wire receptacle

(14 -30R)

If yo u have 3-wir e receptacle, like this , a 3-wire dryer cord mu st be purc hased locall y.

3-wire receptacle

(10 -30R)

3-Wire Electrical Connection

If your receptacle is a 3-wire receptacle as shown below, you must obtain a 3-wire dryer cord. A dryer cord can usually be found at your local hardware supply, electrical supply or home center. Cord should have closed loop or upturned end wire terminating connectors.

3- wire receptacle

( 10-30R)

Typical 3- Wire Dryer Cord 240V/30 amp NEMA 10-30 Type SRDT

A If the dryer is installed in a mobile home, recreational vehicles, new branch-circuit installations or in areas where local codes do not permit grounding, only a 4-wire power supply cord shall be used.

To change the cord:

1.Make sure that the dryer is not plugged into any power outlet.

B DO NOT plug end of dryer power cord into a live receptacle before connecting dryer power cord to dryer terminals and closing junction/splitter box as described below.

B DO NOT repair old power supply cords. Power cord must be changed only by a qualified person. There is a risk of electric shock!

2.Remove the screw from the cover of the junction box located at the top rear of the dryer.

3.Remove the red, white and black wire from the terminal block.

4.Remove the green ground wire from the ground terminal.

5.Loosen the strain relief clamp holding the 4-wire cable.

6.Thread the 4-wire cable out through the strain relief clamp.

7.Thread the new 3-wire dryer cord through the strain relief clamp.

8.Attach the power cord Ground conductor

(the center wire) to the terminal labeled N.

8 - EN

Image 8
Contents Front-Loading Dryer DV 17540 NBL00 Page Read the instructions Useful information Explanation of symbols Important safety informationPlease read this manual first Has started Technical Specifications OverviewFirst Use MachineYour Dryer OverviewImportant Safety Instructions Savethese Instructions Installation Instructions Awarning Risk of fire Wire Electrical ConnectionElectrical connection To change the cordAppropriate installation location Grounding InstructionsMinimum Installation Clearances Use on top of a washing machineVentilation Requirements Alcove or Closet Built-under Sides Top Rear FrontSilently and vibration-free Adjusting the feetVentilation duct and connection Destroying packaging material Care must be taken not to pinch or bend the ductsOperating Instructions Page Start/Pause/Cancel button Cancel Audio Warning Control panelOn/Off button Program selector knobLoading door Turning on the dryerMain programs Permanent Press / Synthetics max .5 kgSpecial programs Automatic Dry / Mixed Fabric max .5 kgMini max .2 kg Shirts max .5 kgStarting the Program Progress of programChanging the program after the program has started Auxiliary functionsFilter cleaning End of programTechnical Specifications EnusSelect the appropriate Program Quick Start-up InstructionsOpen loading door Push the on / OFF button to on Sensor User maintenance and cleaning instructionsLint filter Troubleshooting Deactivate the childproof lockTurn off the dryer and remove Flashes Dryer ends the program without