Bosch Appliances WTA 3510, WTL 5410 manual Additional Grounding Procedure, Electrical Receptacle

Page 16

Additional Grounding Procedure

Some local codes may require a separate ground. In such cases, the required accessory ground wire, clamp and screw must be purchased separately.

Never ground the dryer to plastic plumbing lines, gas lines or water pipes.

Electrical Receptacle

The receptacle for the dryer cord must be located so that the power supply cord will be accessible when the dryer is in the installed position.

Venting

The WTA 3510, electric vented dryer, is intended to be vented to the outdoors. To prevent build-up of moisture and accumulation of lint indoors, as well as to maintain maximum drying efficiency, it is recommended that the Bosch WTA 3510 be vented to the outdoors.

Ductwork

Four-inch (approx. 100 mm) diameter ducting should be used. Use either rigid metal or flexible metal ducting material. DO NOT use non-metal duct with this dryer.

Exhaust ducts should be as straight as possible. Exhaust ducting longer than recommended can extend drying time, can collect lint and may effect dryer performance. Joints should be secured with duct tape. DO NOT use screws to secure joints as lint can collect on the screws. See Step 4, Exhaust Duct, in following section titled INSTALLATION for recommended routing and duct length calculations.

Exhaust Vent Hood

The exhaust duct must end with an approved exhaust vent hood with swing out damper(s). DO NOT use an exhaust vent hood with magnetic latches. To avoid restriction of exhaust the outlet must be a minimum of 12 inches (30 cm) above ground level, or any other obstructing surface. See Figure 17.

Condensate Drain

The WTL 5410, electric condensation dryer, dries by condensing the moisture from the dryer air and then pumping this condensate out of the dryer.

The WTL 5410 must have its condensate hose connected to a suitable drain. See Step 5, Condensate Hose Connection, in the following section titled

INSTALLATION.

Stacking Kit

A stacking kit is supplied with each dryer in order to stack Bosch dryer upon a Bosch washing machine. This part is only necessary if stacking the units is desired.

Stacking Kit with Pull(out(tray - WTZ 1180

As an additional accessory for purchase, Bosch offers a stacking kit for a Bosch washer and dryer that incorporates a pull-out-tray. The tray offers an area for folding and easier unloading of the dryer. See your local dealer for availability and price.

16

Image 16
Contents WTA Electric Vented Dryer Page Installer Keep These Instructions for Future ReferenceImportant Safety Instructions Important Safety Instructions Grounding InstructionsAbout Your Dryer Getting to Know Your DryerBefore Using for the First Time Energy Saving TipsOperating Tips Getting StartedCycle Selection Chart Recommendations OperationRO UO R Turn the dryer onAdd Fabric Softener Sheet, if desired Close the DoorSelect the Drying Cycle Desired To use Electronic Auto Dry CyclesSelect Additional FUNCTIONS, if desired ``End of Cycle Signal``Delicates Lint Filter Care and CleaningHeat Exchanger WTL models only Service and Repair 800/944-2904Moisture Sensor Frost Protection WTL models onlySELF-HELP Statement of Warranties Bosch Clothes Dryers ExclusionsTools Needed for Installation Parts Supplied for InstallationParts Needed for Installation Model WTA 3510 only IntroductionAdditional Grounding Procedure Electrical ReceptacleVenting DuctworkTechnical Data Builtin Installation Installation Step Position Dryer near Installation AreaStep Unpack the Dryer Step Inspect the DryerChecking/Installing Exhaust Ducting Maximum length of ductRigid Duct Flexible Duct StepElectrical Connection, 4-Wire Electrical Connection, 3-WireStep Electrical To Change CordStep Position and Level the Dryer Step Connect Duct System to Dryer Model WTA 3510 only Step Final Check List1101 en 5550 006