Alliance Laundry Systems TMB1276C Service Schedule Menu, Daily Menu Service, Monthly Menu Service

Page 42

Maintenance

Service Schedule Menu

Daily

 

Monthly

 

 

 

Quarterly

 

Bi-Annually

 

 

 

Service Schedule Menu

TMB1334R

Figure 51

Press from Cycle Menu to enter Service Schedule Menu. The Service Schedule Menu provides a user with a time based service reminder list. The list is broken up into “Daily”, “Monthly”, “Quarterly” and “Bi-Annually” Menus. Press

the , , or keypad to navigate to

a menu item. Press the keypad when menu is

selected. Press the keypad to return to Cycle Menu.

Daily Menu (Service)

Daily Maintenance Reminders:

1.Inspect the area surrounding dryers, remove all combustible materials, including lint.

2.Check cylinder for foreign objects to avoid damage to clothing and equipment.

3.Clean lint from lint compartment and screen to maintain proper airflow and avoid overheating.

Service Schedule

TMB1335R

Figure 52

The Daily Menu contains all daily service reminders

that need to be performed. Press the keypad to return to the Service Menu.

Monthly Menu (Service)

Monthly Maintenance Reminders:

1.Remove lint and debris from inside exhaust duct to maintain proper airflow and avoid overheating.

2.Carefully wipe any accumulated lint off the cabinet high limit thermostat and thermistor, including perforated cover. Lint buildup will act as an insulator, causing machine to overheat.

3.Clean lint and debris buildup from blower to maintain proper airflow, to avoid overheating and prevent possible vibration.

Service Schedule

TMB1336R

Figure 53

The Monthly Menu contains all monthly service

reminders that need to be performed. Press the keypad to return to the Service Menu.

40

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

70444801

Image 42
Contents Tumble Dryer Page Contents Modify Cycle Segment Menu Navigation Auto Ignition Retry Gas Models Only Air Flow Switch Errors Introduction Model IdentificationNameplate Location About the Control Power Failure RecoveryPreliminary Information CommunicationsEntering Program Mode IR Communications Error MenuRestore to Factory Defaults IR Communications MenuUniLinc Identification Operational KeypadOperation Modes Reversing Mode reversing models only End of Cycle ModeExtended Tumble Mode Entering Diagnostic Mode From Idle ModeMachine Cycle Operation Machine Cycle Definition and OperationRotation Sensor Equipped Machines Cycle MenuTo Start a Cycle 3000 Run MenuContrast/Backlight Menu Close Door MenuRun Diagnostic Menu TempTemp and Moisture Menu Cycle01 Towels Moisture Dry Cotton Segment01 0500Error Menu Cycle Stopped MenuPress Stop Key to Abort Cycle Open Door Menu Clean Lint Screen MenuService Moisture Sensor Menu Load Sensed MenuMenu Navigation UniLincDisplay Screen Maps System Menu Map TreeService Menu Map Tree Run Menu Map TreeProgramming UniLinc System MenuSave Changes Menu Program Menu Program MenuModify Cycle Available Characters Cycle, Segment and Step Programming Flow Diagram Modify Cycle Segment Menu NavigationLanguage Menu Global SetupGlobal Setup Menu BannersCurrent Date Date/Time MenuBanners Menu Day of WeekRapid Advance Menu Key Pad End of Cycle VolumeTime External Signal Enable Audio MenuMiscellaneous Menu Ignition Retry MenuTemperature Menu Reverse Cylinder Menu if equippedMoisture Menu if equipped TemperatureCool Down Menu TimeFactory Defaults Menu TemperaturesOnly Diagnostics Are Disabled DiagnosticsDiagnostic Menu Test MenuTest Cycle Chart Step Advance Comments3029 Inputs Outputs MenuAlarms Menus Machine ID MenuMachine Errors Air Flow Switch Errors Rotation Sensor ErrorAuto Ignition Retry Gas Models Only Fan Motor Centrifugal Switch Error Moisture Sensor ErrorFan Motor Contactor Error DIP Switch/Harness Index Mismatch ErrorLaundry Management Laundry Management MenusService Schedule Menu Daily Menu ServiceMonthly Menu Service Quarterly Maintenance Reminders Quarterly Menu Service Bi-Annual Menu ServiceCycle Charts OFF