Graco 308550ZAD Air Exhaust Ventilation, Fire and Explosion Hazard, Venting Exhaust AIR

Page 11

Installation

Air Exhaust Ventilation

WARNING

FIRE AND EXPLOSION HAZARD

Be sure to read and follow the warnings and precautions regarding TOXIC FLUID HAZARD, and FIRE OR EXPLO- SION HAZARD on page 4, before op- erating this pump.

Be sure the system is properly ventilated for your type of installation. You must vent the exhaust to a safe place, away from people, animals, food handl- ing areas, and all sources of ignition when pumping flammable or hazardous fluids.

Diaphragm failure will cause the fluid being pumped to exhaust with the air. Place an appropri- ate container at the end of the air exhaust line to catch the fluid. See Fig. 6.

The air exhaust port is 3/4 npt(f). Do not restrict the air exhaust port. Excessive exhaust restriction can cause erratic pump operation.

If the muffler (P) is installed directly to the air exhaust port, apply PTFE thread tape or anti–seize thread lubricant to the muffler threads before assembly.

To provide a remote exhaust:

1.Remove the muffler (P) from the pump air exhaust port.

2.Install an electrically conductive air exhaust hose

(T) and connect the muffler (P) to the other end of the hose. The minimum size for the air exhaust hose is 3/4 in. (19 mm) ID. If a hose longer than 15 ft (4.57 m) is required, use a larger diameter hose. Avoid sharp bends or kinks in the hose. See Fig. 6.

3.Place a container (U) at the end of the air exhaust line to catch fluid in case a diaphragm ruptures.

VENTING EXHAUST AIR

E F C B

KEY

AAir supply line

BBleed-type master air valve (required for pump)

CAir regulator

DAir line quick disconnect

EMaster air valve (for accessories)

FAir line filter

P Muffler

TElectrically conductive air exhaust hose

UContainer for remote air exhaust

A

D

T

Fig. 6

U

P

04617

308550 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Important Safety Instructions Instructions Parts ListModels Table of ContentsEquipment Misuse Hazard SymbolsToxic Fluid Hazard Toxic Fluid Hazard InstallationGeneral Information Tighten Screws Before First UseGround all of this equipment GroundingAir Line Typical FLOOR-MOUNT Installation Fluid Outlet Line Installation of Remote Pilot Air Lines Mountings Fluid Suction LineBolt Tightening Sequence Flange ConnectionsFluid Pressure Relief Valve Changing the Orientation of the Fluid Inlet and Outlet PortsVenting Exhaust AIR Air Exhaust VentilationFire and Explosion Hazard Flush the Pump Before First Use Pressure Relief ProcedureStarting and Adjusting the Pump OperationMaintenance Problem Cause Solution TroubleshootingTroubleshooting Tools Required ServiceRepairing the Air Valve DisassemblyReassembly Relieve the pressure. Disconnect all hoses Ball Check Valve RepairDiaphragm Repair Reassembly Standard Diaphragms Reassembly Overmolded Diaphragms 105 19 402 24 104 403 Bearing and Air Gasket Removal Detail of Air Valve Bearings Husky 2150 Polypropylene and Pvdf Pumps, Series a Pump MatrixFor Husky 2150 Polypropylene and Pvdf Pumps, Series a Repair Kit MatrixParts Air Motor Parts List Matrix ColumnMuffler Fluid Section Parts List Matrix ColumnDiaphragm Parts List Matrix Column Seat Parts List Matrix ColumnBall Parts List Matrix Column 114 Torque Sequence Side View Pump Mounting Hole Pattern DimensionsFront View Dimension SST Center Aluminum Polypropylene Pvdf Cover 14-0.8 MPa, 1.4-8 bar Technical DataFluid Flow GPM lpm Performance ChartFeet meters Psi MPa, barGraco Information Graco Warranties
Top Page Image Contents