Humminbird 937C DF COMBO, 937C COMBO manual View Preset Keys, Exit KEY, Info KEY, Mark/Goto Key

Page 36

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 36

VIEW PRESET KEYS

The VIEW PRESET keys are used to program your three favorite views for quick retrieval. Instead of using the VIEW key to cycle through every view to find the one you want, you can program the VIEW PRESET

keys to display a specific view immediately. To program each VIEW PRESET key, use the VIEW key to cycle to the view you want to store. Press and hold one of the VIEW PRESET keys for several seconds. A series of audible chirps will be heard indicating that the view has been programmed to the key. You can store up to three views, one on each key.

EXIT KEY

The EXIT key has multiple functions, depending on the situation:

If an alarm is sounding, pressing EXIT will cancel the alarm.

If a menu tab is selected, pressing EXIT will exit the menu mode and return to the view.

If a menu is active, pressing EXIT will return to the previous level in the menu system.

Pressing EXIT will cycle through the available views in reverse order.

If Freeze Frame is active, pressing EXIT will return to a scrolling display.

If the Cursor is active, pressing EXIT will remove the cursor from the display.

INFO KEY

(937c DF Combo and 937c Combo models only)

Press the INFO key while in any navigation view to display information about objects that are nearest to an active cursor.

If the cursor is not active, the following menu will be displayed. Use the 4-WAY Cursor Control key to select Nearest Port, Nearest Tide Station or Nearest Current Station, then use the RIGHT Cursor key to display the requested information.

NOTE: The built-in Uni-Map™ does not contain Port, Tide or Current information. This information is only available from optional purchase MMC/SD cards.

MARK/GOTO KEY

(937c DF Combo and 937c Combo models only)

Press the MARK key while in any view to mark the position of a waypoint, either at the current boat location, or, if the Cursor is active, at the current Cursor location.

If the Cursor is active, pressing the GOTO key while in any view creates a waypoint and starts navigation towards that waypoint. If the Cursor is not active, pressing the GOTO key displays the list of waypoints, so that you can select the waypoint towards which you want to navigate.

ZOOM (+/-) KEY

(937c DF Combo and 937c Combo models only)

Press the - or + ZOOM keys while in any of the Navigation Views or the Sonar Zoom View to change the scale of the view to appear closer or farther away.

31

Image 36
Contents Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Series Introduction HOW the 900 Series WorksSingle Beam Sonar Dualbeam Plus SonarMULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD SlotAccessory BUS Installation OverviewAccessory Bus 900 Series has a wide variety of configurationsControl Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head TemperatureTransducer Installation Connecting the Control Head Power Cable to the BoatTransom Transducer Installation To determine transducer mounting locationDetermine transducer mounting location Route the transducer cableCorner of the template Moves clockwise as the boat movesConfirm that the pivot angle has not changed Normal CavitationTo attach the pivot to the transducer Dual frequency unit Attaching the BracketOrder to gain access to the mounting screws, Force is necessary to pivot the assemblyTo route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Permanently mount the transducer Route the cableMake sure the position of the transducer is marked Inside the HullTrolling Motor Transducer Installation Test and Finish the Transducer InstallationStem Mounting with AN Existing 1 14 Thread Stem If you have… Then useHand-tighten only Follow these steps to stem mount the GPS receiverAccess Under Mounting Location To the cable as shownNo Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver OperationSpeed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel Testing the System Installation To test the installationGetting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen WHAT’S on the Sonar Display TriplogUnderstanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key View KEY Menu KEYWAY Cursor Control KEY Fishing requirements see View Menu TabView Preset Keys Exit KEYInfo KEY MARK/GOTO KEYViews Views and ReadoutsSonar views Navigation viewsSonar View Sonar Zoom ViewSonar View Sonar Zoom View Split Sonar ViewBIRD’S EYE View Bird’s Eye ViewChart/Bird’s Eye Combo View Chart View with Active CursorChart/Sonar Combo View 1112Chart Orientation Chart View with Cursor PresentNavigation To save the marked position as a waypoint Waypoints, Routes and TracksNavigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Menu System Press MenuSonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Exit Normal operation by powering your 900 Series off Normal OperationSimulator SimulatorAccessory Test Self Test Accessory TestSystem Status Self TestGPS Diagnostic View Sonar X-PRESS MenuActive Side SensitivitySplit Position To adjust the Upper Range To adjust the Lower RangeUpper Range Lower RangeChart Speed Zoom LevelBottom Lock Sonar ColorsHighlight Split Position on the Navigation X-Press Menu Navigation X-Press MenuSave Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid Sonar Menu TAB Beam SelectTo use Beam Select Highlight Beam Select on the Sonar main menuTo change the Fish ID Sensitivity setting Fish ID+Fish ID Sensitivity To turn Fish ID+ on or offTo adjust the Bottom View Bottom ViewZoom Width To change the Zoom WidthKHZ Sensitivity Depth LinesSurface Clutter Noise FilterMAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints North Reference Trolling Grid RotationTrackpoint Interval Track MIN DistanceMAP Datum Export ALL NAV DataDelete ALL NAV Data Chart Menu TAB Chart Detail LevelTo change the Chart Detail Level setting To change the Map Borders settingLAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset Depth Alarm Fish ID AlarmLOW Battery Alarm Temp AlarmOFF Course Alarm Arrival AlarmDrift Alarm To change the Off Course Alarm settingAlarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu Setup Menu TAB To change the Units Depth settingTo change the Units Temp setting Units DepthUser Mode Units DistanceUnits Speed LanguageTriplog Reset Restore DefaultsTo Reset Triplog To Restore DefaultsDefault Sonar View Customized Sonar View To Select ReadoutsDepth Offset Temp OffsetSpeed Calibration Local Time ZoneDaylight Saving Time Position FormatNmea Output SonarFollowing Nmea sentences are output To turn Nmea Output on or offAccessories Menu TAB Views Menu TABTo Change the View Status of Any View Highlight the View main menu tabTroubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Display Problems Problem Possible CauseFinding the Cause of Noise Other electronic devicesNoise re-appears Boat’s engineYear Limited Warranty Humminbird Service PolicyReturning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Specifications Power OutputAppendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird