Humminbird 937C COMBO, 937C DF COMBO manual SET MAP Offset, Clear MAP Offset, Alarms Menu TAB

Page 71

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 71

SET MAP OFFSET

(Advanced)

Set Map Offset allows you to change the map offset used by the 900 Series™.

NOTE: The Map Offset will be applied to all maps and not just the map that requires the correction. The Map Offset should be cleared if a different map is to be used.

To change the Map Offset setting:

1. Activate the cursor and move it location where the Map Offset will be applied.

NOTE: The cursor must be active in order for this procedure to work.

2.Make sure you are in Advanced User Mode, then highlight Set Map Offset on the Navigation main menu.

3. Use the RIGHT 4-WAY Cursor Control key to set the Map Offset. A confirmation dialog box will appear to allow you to change your mind, or to confirm your choice. If the cursor was not active before you began this procedure, you will see an error message. Exit the menu, set the cursor, then try again.

CLEAR MAP OFFSET

(Advanced)

Clear Map Offset allows you to clear the Map Offset. Clear Map Offset is only accessible if a Map Offset is currently active.

To Clear Map Offset:

1.Make sure you are in Advanced User Mode, then highlight Clear Map Offset on the Navigation main menu.

2.Use the RIGHT 4-WAY Cursor Control key to clear the Map Offset.

Alarms Menu

ALARMS MENU TAB

From any view, press the MENU key twice to access the Main Menu System. The Alarms tab will be the default selection.

NOTE: When an alarm is triggered, you can silence it by pressing any key. The alarm will be silenced, and will not be triggered again until a new instance of the alarm condition is detected.

66

Image 71
Contents Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Dualbeam Plus Sonar Series IntroductionHOW the 900 Series Works Single Beam SonarMulti-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot900 Series has a wide variety of configurations Accessory BUSInstallation Overview Accessory BusGimbal Mounting the Control Head Control Head InstallationBasic installation tasks that you must perform include Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control HeadConnecting the Control Head Power Cable to the Boat Transducer InstallationRoute the transducer cable Transom Transducer InstallationTo determine transducer mounting location Determine transducer mounting locationMoves clockwise as the boat moves Corner of the templateNormal Cavitation Confirm that the pivot angle has not changedAttaching the Bracket To attach the pivot to the transducer Dual frequency unitForce is necessary to pivot the assembly Order to gain access to the mounting screws,To route the transom transducer cable all transducers Determine the transducer mounting location Inside the Hull Transducer InstallationTrial installation Inside the Hull Permanently mount the transducerRoute the cable Make sure the position of the transducer is markedTest and Finish the Transducer Installation Trolling Motor Transducer InstallationFollow these steps to stem mount the GPS receiver Stem Mounting with AN Existing 1 14 Thread StemIf you have… Then use Hand-tighten onlyTo the cable as shown Access Under Mounting LocationFinish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationHand tighten only Speed Accessory InstallationInstall the Speed accessory Rotating Retaining Axial Clip to Remove Paddlewheel Cleaning the Speed accessoryRouting the speed cable to the control head To test the installation Testing the System InstallationSeries 937c DF Combo Title Screen Getting Started Using Your 900 SeriesPowering UP the Control Head Triplog WHAT’S on the Sonar DisplayBottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window MARK/GOTO key Info key Zoom +/- key POWER/LIGHT KEYKEY Functions Fishing requirements see View Menu Tab View KEYMenu KEY WAY Cursor Control KEYMARK/GOTO KEY View Preset KeysExit KEY Info KEYNavigation views ViewsViews and Readouts Sonar viewsSonar View Sonar ViewSonar Zoom View Split Sonar View Sonar Zoom ViewBird’s Eye View BIRD’S EYE ViewChart View with Active Cursor Chart/Bird’s Eye Combo View1112 Chart/Sonar Combo ViewChart View with Cursor Present Chart OrientationNavigation Waypoints, Routes and Tracks To save the marked position as a waypointNavigate to a Waypoint or Position ADD a Waypoint Target or Trolling Grid Chart View with TargetChart View with Grid Save or Clear a Current Track Press Menu Menu SystemStart-Up Options Menu Sonar Tab, Normal ModeSTART-UP Options Menu Simulator Exit Normal operation by powering your 900 Series offNormal Operation SimulatorSelf Test Accessory TestSelf Test Accessory Test System StatusSonar X-PRESS Menu GPS Diagnostic ViewSplit Position Active SideSensitivity Lower Range To adjust the Upper RangeTo adjust the Lower Range Upper RangeSonar Colors Chart SpeedZoom Level Bottom LockNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuSave Current Route Save Current TrackClear Current Track Remove Grid Cancel NavigationRemove Target Highlight Beam Select on the Sonar main menu Sonar Menu TABBeam Select To use Beam SelectTo turn Fish ID+ on or off To change the Fish ID Sensitivity settingFish ID+ Fish ID SensitivityTo change the Zoom Width To adjust the Bottom ViewBottom View Zoom WidthNoise Filter KHZ SensitivityDepth Lines Surface ClutterTransducer Select MAX DepthWater Type Navigation Menu TAB Temperature GraphColor BAR Waypoints TracksRoutes Track MIN Distance North ReferenceTrolling Grid Rotation Trackpoint IntervalDelete ALL NAV Data MAP DatumExport ALL NAV Data To change the Map Borders setting Chart Menu TABChart Detail Level To change the Chart Detail Level settingShaded Depth LAT/LON GridSpot Soundings Clear MAP Offset Alarms Menu TABSET MAP Offset Temp Alarm Depth AlarmFish ID Alarm LOW Battery AlarmTo change the Off Course Alarm setting OFF Course AlarmArrival Alarm Drift AlarmHighlight Alarm Tone on the Alarms main menu Alarm ToneTo change the Alarm Tone setting Units Depth Setup Menu TABTo change the Units Depth setting To change the Units Temp settingLanguage User ModeUnits Distance Units SpeedTo Restore Defaults Triplog ResetRestore Defaults To Reset TriplogTo Select Readouts Default Sonar View Customized Sonar ViewLocal Time Zone Depth OffsetTemp Offset Speed CalibrationPosition Format Daylight Saving TimeTo turn Nmea Output on or off Nmea OutputSonar Following Nmea sentences are outputHighlight the View main menu tab Accessories Menu TABViews Menu TAB To Change the View Status of Any ViewSeries Defaults to Simulator with a Transducer Attached TroubleshootingSeries Doesn’t Power Up Problem Possible Cause Display ProblemsBoat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appearsHumminbird Service Policy Year Limited WarrantyFor IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Power Output SpecificationsAlign with transom Appendix aPlace on bottom of hull Appendix B Contact Humminbird