Humminbird 937C DF, 937C COMBO Setup Menu TAB, Units Temp, To change the Units Depth setting

Page 75

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 75

SETUP MENU TAB

From any view, press the MENU key twice to access the tabbed Main Menu System, then press the RIGHT cursor key until the Setup tab is selected.

NOTE: Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode and what accessories are attached to the control head.

Setup Menu

UNITS - DEPTH

Units - Depth selects the units of measure for all

depth-related readouts.

To change the Units - Depth setting:

1.Highlight Units - Depth on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Depth setting. (Meters [International models only], Feet, Fathoms; Default is Meters for International models, and Feet for Domestic models)

UNITS - TEMP

(International only)

Units - Temp selects the units of measure for all temperature-related readouts. International models only.

To change the Units - Temp setting:

1.Highlight Units - Temp on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Temp setting. (Celsius, Fahrenheit; Default = Celsius)

70

Image 75

Contents Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Dualbeam Plus Sonar Series IntroductionHOW the 900 Series Works Single Beam SonarMulti-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD Slot900 Series has a wide variety of configurations Accessory BUSInstallation Overview Accessory BusControl Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control HeadConnecting the Control Head Power Cable to the Boat Transducer InstallationRoute the transducer cable Transom Transducer InstallationTo determine transducer mounting location Determine transducer mounting locationMoves clockwise as the boat moves Corner of the templateNormal Cavitation Confirm that the pivot angle has not changedAttaching the Bracket To attach the pivot to the transducer Dual frequency unitForce is necessary to pivot the assembly Order to gain access to the mounting screws,To route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Inside the Hull Permanently mount the transducerRoute the cable Make sure the position of the transducer is markedTest and Finish the Transducer Installation Trolling Motor Transducer InstallationFollow these steps to stem mount the GPS receiver Stem Mounting with AN Existing 1 14 Thread StemIf you have… Then use Hand-tighten onlyTo the cable as shown Access Under Mounting LocationFinish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationSpeed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel To test the installation Testing the System InstallationGetting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen Triplog WHAT’S on the Sonar DisplayUnderstanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key Fishing requirements see View Menu Tab View KEYMenu KEY WAY Cursor Control KEYMARK/GOTO KEY View Preset KeysExit KEY Info KEYNavigation views ViewsViews and Readouts Sonar viewsSonar View Sonar Zoom ViewSonar View Split Sonar View Sonar Zoom ViewBird’s Eye View BIRD’S EYE ViewChart View with Active Cursor Chart/Bird’s Eye Combo View1112 Chart/Sonar Combo ViewChart View with Cursor Present Chart OrientationNavigation Waypoints, Routes and Tracks To save the marked position as a waypointNavigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Press Menu Menu SystemSonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Simulator Exit Normal operation by powering your 900 Series offNormal Operation SimulatorSelf Test Accessory TestSelf Test Accessory Test System StatusSonar X-PRESS Menu GPS Diagnostic ViewActive Side SensitivitySplit Position Lower Range To adjust the Upper RangeTo adjust the Lower Range Upper RangeSonar Colors Chart SpeedZoom Level Bottom LockNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuSave Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid Highlight Beam Select on the Sonar main menu Sonar Menu TABBeam Select To use Beam SelectTo turn Fish ID+ on or off To change the Fish ID Sensitivity settingFish ID+ Fish ID SensitivityTo change the Zoom Width To adjust the Bottom ViewBottom View Zoom WidthNoise Filter KHZ SensitivityDepth Lines Surface ClutterMAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints Track MIN Distance North ReferenceTrolling Grid Rotation Trackpoint IntervalMAP Datum Export ALL NAV DataDelete ALL NAV Data To change the Map Borders setting Chart Menu TABChart Detail Level To change the Chart Detail Level settingLAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset Temp Alarm Depth AlarmFish ID Alarm LOW Battery AlarmTo change the Off Course Alarm setting OFF Course AlarmArrival Alarm Drift AlarmAlarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu Units Depth Setup Menu TABTo change the Units Depth setting To change the Units Temp settingLanguage User ModeUnits Distance Units SpeedTo Restore Defaults Triplog ResetRestore Defaults To Reset TriplogTo Select Readouts Default Sonar View Customized Sonar ViewLocal Time Zone Depth OffsetTemp Offset Speed CalibrationPosition Format Daylight Saving TimeTo turn Nmea Output on or off Nmea OutputSonar Following Nmea sentences are outputHighlight the View main menu tab Accessories Menu TABViews Menu TAB To Change the View Status of Any ViewTroubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Problem Possible Cause Display ProblemsBoat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appearsHumminbird Service Policy Year Limited WarrantyReturning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Power Output SpecificationsAppendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird