Humminbird 937C COMBO manual START-UP Options Menu, Sonar Tab, Normal Mode, Start-Up Options Menu

Page 50

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 50

User Mode (Normal or Advanced): An Advanced Mode is provided for users who desire the highest level of control over the 900 Series™ and Normal Mode for users who desire greater simplicity and fewer menu choices. Additional Advanced menu choices will be displayed throughout the menu system when you navigate to specific menus while in Advanced Mode. Any changes made while in Advanced Mode will remain in effect after you switch back to Normal Mode. See Setup Menu Tab: User Mode for specific instructions on changing to the User Mode.

NOTE: The 900 Series™ defaults to Advanced User Mode on start-up.

Sonar Tab, Normal Mode

Sonar Tab, Advanced Mode

Total Screen Update: when you change any menu settings that affect the Sonar View, the view will update immediately (i.e. you don’t have to exit the menu to apply the change to the screen).

START-UP OPTIONS MENU

Press the MENU key when the Title screen is displayed to access the Start-Up Options menu.

Start-Up Options Menu

Use the UP or DOWN 4-WAY Cursor keys to position the cursor, then the RIGHT Cursor key to select one of the following choices. If you wait too long, the system will default to whichever menu mode happens to be highlighted:

•Normal

•Simulator

•System Status.

See the following paragraphs for more information about each of these choices.

45

Image 50

Contents Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Single Beam Sonar Series IntroductionHOW the 900 Series Works Dualbeam Plus SonarMULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD SlotAccessory Bus Accessory BUSInstallation Overview 900 Series has a wide variety of configurationsGimbal Mounting the Control Head Control Head InstallationBasic installation tasks that you must perform include Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head TemperatureTransducer Installation Connecting the Control Head Power Cable to the BoatDetermine transducer mounting location Transom Transducer InstallationTo determine transducer mounting location Route the transducer cableCorner of the template Moves clockwise as the boat movesConfirm that the pivot angle has not changed Normal CavitationTo attach the pivot to the transducer Dual frequency unit Attaching the BracketOrder to gain access to the mounting screws, Force is necessary to pivot the assemblyTo route the transom transducer cable all transducers Determine the transducer mounting location Inside the Hull Transducer InstallationTrial installation Make sure the position of the transducer is marked Permanently mount the transducerRoute the cable Inside the HullTrolling Motor Transducer Installation Test and Finish the Transducer InstallationHand-tighten only Stem Mounting with AN Existing 1 14 Thread StemIf you have… Then use Follow these steps to stem mount the GPS receiverAccess Under Mounting Location To the cable as shownNo Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver OperationHand tighten only Speed Accessory InstallationInstall the Speed accessory Rotating Retaining Axial Clip to Remove Paddlewheel Cleaning the Speed accessoryRouting the speed cable to the control head Testing the System Installation To test the installationSeries 937c DF Combo Title Screen Getting Started Using Your 900 SeriesPowering UP the Control Head WHAT’S on the Sonar Display TriplogBottom Presentation Understanding Sonar HistoryReal Time Sonar RTS Window MARK/GOTO key Info key Zoom +/- key POWER/LIGHT KEYKEY Functions WAY Cursor Control KEY View KEYMenu KEY Fishing requirements see View Menu TabInfo KEY View Preset KeysExit KEY MARK/GOTO KEYSonar views ViewsViews and Readouts Navigation viewsSonar View Sonar ViewSonar Zoom View Sonar Zoom View Split Sonar ViewBIRD’S EYE View Bird’s Eye ViewChart/Bird’s Eye Combo View Chart View with Active CursorChart/Sonar Combo View 1112Chart Orientation Chart View with Cursor PresentNavigation To save the marked position as a waypoint Waypoints, Routes and TracksNavigate to a Waypoint or Position ADD a Waypoint Target or Trolling Grid Chart View with TargetChart View with Grid Save or Clear a Current Track Menu System Press MenuStart-Up Options Menu Sonar Tab, Normal ModeSTART-UP Options Menu Simulator Exit Normal operation by powering your 900 Series offNormal Operation SimulatorSystem Status Accessory TestSelf Test Accessory Test Self TestGPS Diagnostic View Sonar X-PRESS MenuSplit Position Active SideSensitivity Upper Range To adjust the Upper RangeTo adjust the Lower Range Lower RangeBottom Lock Chart SpeedZoom Level Sonar ColorsHighlight Split Position on the Navigation X-Press Menu Navigation X-Press MenuSave Current Route Save Current TrackClear Current Track Remove Grid Cancel NavigationRemove Target To use Beam Select Sonar Menu TABBeam Select Highlight Beam Select on the Sonar main menuFish ID Sensitivity To change the Fish ID Sensitivity settingFish ID+ To turn Fish ID+ on or offZoom Width To adjust the Bottom ViewBottom View To change the Zoom WidthSurface Clutter KHZ SensitivityDepth Lines Noise FilterTransducer Select MAX DepthWater Type Navigation Menu TAB Temperature GraphColor BAR Waypoints TracksRoutes Trackpoint Interval North ReferenceTrolling Grid Rotation Track MIN DistanceDelete ALL NAV Data MAP DatumExport ALL NAV Data To change the Chart Detail Level setting Chart Menu TABChart Detail Level To change the Map Borders settingShaded Depth LAT/LON GridSpot Soundings Clear MAP Offset Alarms Menu TABSET MAP Offset LOW Battery Alarm Depth AlarmFish ID Alarm Temp AlarmDrift Alarm OFF Course AlarmArrival Alarm To change the Off Course Alarm settingHighlight Alarm Tone on the Alarms main menu Alarm ToneTo change the Alarm Tone setting To change the Units Temp setting Setup Menu TABTo change the Units Depth setting Units DepthUnits Speed User ModeUnits Distance LanguageTo Reset Triplog Triplog ResetRestore Defaults To Restore DefaultsDefault Sonar View Customized Sonar View To Select ReadoutsSpeed Calibration Depth OffsetTemp Offset Local Time ZoneDaylight Saving Time Position FormatFollowing Nmea sentences are output Nmea OutputSonar To turn Nmea Output on or offTo Change the View Status of Any View Accessories Menu TABViews Menu TAB Highlight the View main menu tabSeries Defaults to Simulator with a Transducer Attached TroubleshootingSeries Doesn’t Power Up Display Problems Problem Possible CauseNoise re-appears Finding the Cause of NoiseOther electronic devices Boat’s engineYear Limited Warranty Humminbird Service PolicyFor IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Specifications Power OutputAlign with transom Appendix aPlace on bottom of hull Appendix B Contact Humminbird