Humminbird 937C DF COMBO, 937C COMBO Nmea Output, Sonar, Following Nmea sentences are output

Page 81

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:12 AM Page 81

NMEA OUTPUT

(Advanced)

NMEA Output turns the NMEA output on or off. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)

The following NMEA sentences are output:

DPT- Depth

MTW - Water Temperature

GLL - Lat/Lon Position

GGA - GPS Fix Data

RMC - Recommended Minimum Specific GNSS Data

VTG - Course Over Ground and Ground Speed

ZDA - Time and Date

When navigating, the following NMEA sentences are also output:

APB - Autopilot Sentence B

BWR - Bearing and Distance to Waypoint

RMB - Recommended Minimum Navigation Info

To turn NMEA Output on or off:

1.Make sure you are in Advanced User Mode, then highlight NMEA Output on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the NMEA Output to On or Off (Off, On, Default = Off).

SONAR

(937c DF Combo and 937c Combo models only)

Sonar deactivates Sonar and removes the Sonar Views from the view rotation.

To turn Sonar on or off:

1.Highlight Sonar on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Sonar to On or Off (Off, On, Default = On).

76

Image 81

Contents Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird HOW the 900 Series Works Series IntroductionSingle Beam Sonar Dualbeam Plus SonarMulti-Media Card MMC/SD Slot MULTI-MEDIA Card MMC/SD SlotInstallation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurationsControl Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Temperature Plug Cable Connector Assembly to Back of Control HeadConnecting the Control Head Power Cable to the Boat Transducer InstallationTo determine transducer mounting location Transom Transducer InstallationDetermine transducer mounting location Route the transducer cableMoves clockwise as the boat moves Corner of the templateNormal Cavitation Confirm that the pivot angle has not changedAttaching the Bracket To attach the pivot to the transducer Dual frequency unitForce is necessary to pivot the assembly Order to gain access to the mounting screws,To route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Inside the HullTest and Finish the Transducer Installation Trolling Motor Transducer InstallationIf you have… Then use Stem Mounting with AN Existing 1 14 Thread StemHand-tighten only Follow these steps to stem mount the GPS receiverTo the cable as shown Access Under Mounting LocationFinish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationSpeed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel To test the installation Testing the System InstallationGetting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen Triplog WHAT’S on the Sonar DisplayUnderstanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key Menu KEY View KEYWAY Cursor Control KEY Fishing requirements see View Menu TabExit KEY View Preset KeysInfo KEY MARK/GOTO KEYViews and Readouts ViewsSonar views Navigation viewsSonar View Sonar Zoom ViewSonar View Split Sonar View Sonar Zoom ViewBird’s Eye View BIRD’S EYE ViewChart View with Active Cursor Chart/Bird’s Eye Combo View1112 Chart/Sonar Combo ViewChart View with Cursor Present Chart OrientationNavigation Waypoints, Routes and Tracks To save the marked position as a waypointNavigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Press Menu Menu SystemSonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Normal Operation Exit Normal operation by powering your 900 Series offSimulator SimulatorSelf Test Accessory Test Accessory TestSystem Status Self TestSonar X-PRESS Menu GPS Diagnostic ViewActive Side SensitivitySplit Position To adjust the Lower Range To adjust the Upper RangeUpper Range Lower RangeZoom Level Chart SpeedBottom Lock Sonar ColorsNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuSave Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid Beam Select Sonar Menu TABTo use Beam Select Highlight Beam Select on the Sonar main menuFish ID+ To change the Fish ID Sensitivity settingFish ID Sensitivity To turn Fish ID+ on or offBottom View To adjust the Bottom ViewZoom Width To change the Zoom WidthDepth Lines KHZ SensitivitySurface Clutter Noise FilterMAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints Trolling Grid Rotation North ReferenceTrackpoint Interval Track MIN DistanceMAP Datum Export ALL NAV DataDelete ALL NAV Data Chart Detail Level Chart Menu TABTo change the Chart Detail Level setting To change the Map Borders settingLAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset Fish ID Alarm Depth AlarmLOW Battery Alarm Temp AlarmArrival Alarm OFF Course AlarmDrift Alarm To change the Off Course Alarm settingAlarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units DepthUnits Distance User ModeUnits Speed LanguageRestore Defaults Triplog ResetTo Reset Triplog To Restore DefaultsTo Select Readouts Default Sonar View Customized Sonar ViewTemp Offset Depth OffsetSpeed Calibration Local Time ZonePosition Format Daylight Saving TimeSonar Nmea OutputFollowing Nmea sentences are output To turn Nmea Output on or offViews Menu TAB Accessories Menu TABTo Change the View Status of Any View Highlight the View main menu tabTroubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Problem Possible Cause Display ProblemsOther electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engineHumminbird Service Policy Year Limited WarrantyReturning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Power Output SpecificationsAppendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird