Humminbird 937C DF COMBO, 937C COMBO manual Back of Control Head

Page 12

www..reelsche93x Man 531370-1mA - vs4atic.qxd 2/18/2005..com11:11 AM Page 12

1 2 3 4

1 Power

2	Speed	5
		5

3Communications

4Transducer

5Cable Collector Insert

Plug Cable Connector Assembly to

Back of Control Head

9.While holding cables in place in the cable collector insert, thread the cables through the slot in the bottom of the cable collector cover, line up the cable collector insert and cover, then slide the cover into place on the insert.

NOTE: The tab on the Cable Collector insert goes into the slot on the cover.

2

1

4

5

10.Attach the cable collector insert to the cable collector cover using the 2 Phillip screws provided.

11.Place the control head back onto the mounting bracket. Plug in the cable collector assembly to the back of the control head. Cable connectors and cable sockets are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong sockets. Once the cable collector and all cables are plugged into the back of the control head, lock the assembly into place by threading the knurled screw into the threaded insert on the back of the housing. Adjust the control head to the desired viewing angle and secure by tightening the gimbal knobs.

NOTE: You may wish to dress the cabling with nylon wire ties in order to hold the cables together and create a cleaner assembly.

3

1 Cable Collector Insert

2 Screws

3 Cable Collector Cover

The Humminbird® 900 Series™ control head is now ready for operation.

4 Tab on Insert

5 Slot on Cover

7

Image 12

Contents Page Thank YOU Table of Contents Menu System Start-Up Options Menu Contact Humminbird Series Introduction HOW the 900 Series WorksSingle Beam Sonar Dualbeam Plus SonarMULTI-MEDIA Card MMC/SD Slot Multi-Media Card MMC/SD SlotAccessory BUS Installation OverviewAccessory Bus 900 Series has a wide variety of configurationsControl Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Back of Control Head IN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head TemperatureTransducer Installation Connecting the Control Head Power Cable to the BoatTransom Transducer Installation To determine transducer mounting locationDetermine transducer mounting location Route the transducer cableCorner of the template Moves clockwise as the boat movesConfirm that the pivot angle has not changed Normal CavitationTo attach the pivot to the transducer Dual frequency unit Attaching the BracketOrder to gain access to the mounting screws, Force is necessary to pivot the assemblyTo route the transom transducer cable all transducers Inside the Hull Transducer Installation Trial installationDetermine the transducer mounting location Permanently mount the transducer Route the cableMake sure the position of the transducer is marked Inside the HullTrolling Motor Transducer Installation Test and Finish the Transducer InstallationStem Mounting with AN Existing 1 14 Thread Stem If you have… Then useHand-tighten only Follow these steps to stem mount the GPS receiverAccess Under Mounting Location To the cable as shownNo Access Under Mounting Location Finish Routing the Cable and Check GPS Receiver OperationSpeed Accessory Installation Install the Speed accessoryHand tighten only Cleaning the Speed accessory Routing the speed cable to the control headRotating Retaining Axial Clip to Remove Paddlewheel Testing the System Installation To test the installationGetting Started Using Your 900 Series Powering UP the Control HeadSeries 937c DF Combo Title Screen WHAT’S on the Sonar Display TriplogUnderstanding Sonar History Real Time Sonar RTS WindowBottom Presentation POWER/LIGHT KEY KEY FunctionsMARK/GOTO key Info key Zoom +/- key View KEY Menu KEYWAY Cursor Control KEY Fishing requirements see View Menu TabView Preset Keys Exit KEYInfo KEY MARK/GOTO KEYViews Views and ReadoutsSonar views Navigation viewsSonar View Sonar Zoom ViewSonar View Sonar Zoom View Split Sonar ViewBIRD’S EYE View Bird’s Eye ViewChart/Bird’s Eye Combo View Chart View with Active CursorChart/Sonar Combo View 1112Chart Orientation Chart View with Cursor PresentNavigation To save the marked position as a waypoint Waypoints, Routes and TracksNavigate to a Waypoint or Position Chart View with Target Chart View with GridADD a Waypoint Target or Trolling Grid Save or Clear a Current Track Menu System Press MenuSonar Tab, Normal Mode START-UP Options MenuStart-Up Options Menu Exit Normal operation by powering your 900 Series off Normal OperationSimulator SimulatorAccessory Test Self Test Accessory TestSystem Status Self TestGPS Diagnostic View Sonar X-PRESS MenuActive Side SensitivitySplit Position To adjust the Upper Range To adjust the Lower RangeUpper Range Lower RangeChart Speed Zoom LevelBottom Lock Sonar ColorsHighlight Split Position on the Navigation X-Press Menu Navigation X-Press MenuSave Current Track Clear Current TrackSave Current Route Cancel Navigation Remove TargetRemove Grid Sonar Menu TAB Beam SelectTo use Beam Select Highlight Beam Select on the Sonar main menuTo change the Fish ID Sensitivity setting Fish ID+Fish ID Sensitivity To turn Fish ID+ on or offTo adjust the Bottom View Bottom ViewZoom Width To change the Zoom WidthKHZ Sensitivity Depth LinesSurface Clutter Noise FilterMAX Depth Water TypeTransducer Select Temperature Graph Color BARNavigation Menu TAB Tracks RoutesWaypoints North Reference Trolling Grid RotationTrackpoint Interval Track MIN DistanceMAP Datum Export ALL NAV DataDelete ALL NAV Data Chart Menu TAB Chart Detail LevelTo change the Chart Detail Level setting To change the Map Borders settingLAT/LON Grid Spot SoundingsShaded Depth Alarms Menu TAB SET MAP OffsetClear MAP Offset Depth Alarm Fish ID AlarmLOW Battery Alarm Temp AlarmOFF Course Alarm Arrival AlarmDrift Alarm To change the Off Course Alarm settingAlarm Tone To change the Alarm Tone settingHighlight Alarm Tone on the Alarms main menu Setup Menu TAB To change the Units Depth settingTo change the Units Temp setting Units DepthUser Mode Units DistanceUnits Speed LanguageTriplog Reset Restore DefaultsTo Reset Triplog To Restore DefaultsDefault Sonar View Customized Sonar View To Select ReadoutsDepth Offset Temp OffsetSpeed Calibration Local Time ZoneDaylight Saving Time Position FormatNmea Output SonarFollowing Nmea sentences are output To turn Nmea Output on or offAccessories Menu TAB Views Menu TABTo Change the View Status of Any View Highlight the View main menu tabTroubleshooting Series Doesn’t Power UpSeries Defaults to Simulator with a Transducer Attached Display Problems Problem Possible CauseFinding the Cause of Noise Other electronic devicesNoise re-appears Boat’s engineYear Limited Warranty Humminbird Service PolicyReturning Your Unit for Service Series AccessoriesFor IN-WARRANTY service, complete the following steps Specifications Power OutputAppendix a Place on bottom of hullAlign with transom Appendix B Contact Humminbird