Humminbird 531374-1_A manual GPS Receiver Installation, If you have… Then use, Hand-tighten only

Page 23

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:53..coPM Pagem23

NOTE: Due to the wide variety of boat hulls, it is not always possible to obtain high speed depth readings.

NOTE: It is often necessary to make several incremental transducer adjustments before optimum high speed performance is achieved.

Once you have reached a consistently good sonar signal at the desired speeds, you are ready to lock down the transducer settings.

5.Mark the transducer bracket location on the transom with a pencil, then pop up the bracket to reveal the mounting screws. Tighten the stainless steel mounting bracket screws to secure in place.

Hand-tighten only!

GPS RECEIVER INSTALLATION

To optimize performance of the GPS receiver, mount it in an area that has full exposure to the sky. The effective area of reception is 10° above the horizon. Different circumstances determine the mounting method appropriate for your GPS receiver.

If you have…

Then use:

An existing antenna stem with Stem Mount with Existing 1” - 14 Thread Stem standard 1" – 14 thread

Access for cable routing under	Access Under Mounting Location
the mounting location
No access under the mounting	No Access Under Mounting Location
location

STEM MOUNTING WITH AN EXISTING 1" - 14 THREAD STEM

Follow these steps to stem mount the GPS receiver:

NOTE: If you have an existing stem for mounting the GPS receiver, proceed directly to step 2 of the following procedure.

1.Determine the best location to mount your GPS receiver. Preplan and test the cable routing to your control head before any drilling or cutting of your boat surfaces. If you have purchased hardware to stem mount your GPS receiver, follow the instructions included with that hardware to mount the stem (antenna pole).

NOTE: AS-EC10 10' extension cables are available from Humminbird® if your planned routing exceeds 20', (6 m). Maximum cable length, including extensions, should not exceed 50' (16 m).

NOTE: Remember to caulk or seal screw holes and drilled holes as needed to protect your boat from water damage.

18

Image 23

Contents Page Thank You Table of Contents Navigation X-Press Menu Menu System Start-Up Options Menu2D Sonar X-Press Menu 3D Sonar X-Press MenuViews Menu Tab Accessories Menu Tab Troubleshooting Chart Menu TabAlarms Menu Tab Setup Menu Tab2D Sonar Series IntroductionHOW the 900 Series Works 3D SonarSD Slot GPS and CartographyMULTI-MEDIA Card MMC SD Slot 900 Series has a wide variety of configurations Accessory BUSInstallation Overview Accessory BusGimbal Mounting the Control Head Control Head InstallationBasic installation tasks that you must perform include Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Screws provided Plug Cable Connector Assembly to Back of Control HeadIN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer InstallationStepped Hull Transom Transducer InstallationTo determine transducer mounting location Attaching the Bracket To mount the transducer bracket to the boatTo attach the pivot to the transducer But do not completely tightenNormal Cavitation To mount the transducer pivot assembly to the bracketTo adjust the running position of the transducer Routing the Cable To route the transom transducer cableReassemble Fully tightenedDetermine the transducer mounting location Inside the Hull Transducer InstallationTrial installation Transducer Mounted Inside the Hull Permanently mount the transducerRoute the cable Make sure the position of the transducer is markedTrolling Motor Transducer Installation Test and Finish the Transducer InstallationFollow these steps to stem mount the GPS receiver GPS Receiver InstallationIf you have… Then use Hand-tighten onlyTo the cable as shown Access Under Mounting LocationAccess Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationRouting the cable to the control head Install the temperature probe accessoryTo test the installation Testing the System InstallationSeries 947c 3D Combo Title Screen Powering UP the Control HeadTriplog WHAT’S on the 3D Sonar DisplayBait Ball RTS Real Time Sonar Window WHAT’S on the 2D Sonar DisplayBottom Presentation Real Time Sonar RTS WindowMenu KEY POWER/LIGHT KEYKEY Functions View KEYInfo KEY View Preset KeysWAY Cursor Control KEY Exit KEYViews available on your 900 Series are MARK/GOTO KEYViews 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View2D Zoom View 2D Zoom ViewBird’s Eye View Beam Sonar ViewBIRD’S EYE View Beam Sonar ViewChart View with Active Cursor CHART/BIRD’S EYE Combo ViewChart View Chart/Bird’s Eye Combo View with Active CursorChart/2D Combo View CHART/3D Combo ViewCHART/2D Combo View Viewing Cartography Chart OrientationChart View with Cursor Present Waypoints, Routes and Tracks WAYPOINTS, Routes and TracksNavigation SAVE, EDIT, or Delete a Waypoint ADD a Waypoint Target or Trolling Grid Chart View with TargetNavigate to a Waypoint or Position SAVE, Edit or Delete a Route Chart View with GridMenu System Save or Clear a Current TrackEDIT, Delete or Hide Saved Tracks Sonar Tab, Advanced Mode Sonar Tab, Normal ModeNormal Simulator System Status Exit Normal operation by powering your 900 Series offSTART-UP Options Menu Normal OperationSelf Test Self Test Accessory Test GPS Diagnostic ViewSimulator System StatusGPS Diagnostic View Accessory TestGPS Diagnostic View Accessory Test ScreenSplit Position To Adjust Split Screen Position2D Sonar X-PRESS Menu Active SideUpper Range To adjust the SensitivityTo adjust the Upper Range SensitivityBottom Lock Chart SpeedLower Range To change the 2D/3D Priority To adjust the Bottom RangeBottom Range 2D/3D Priority3D Sonar X-Press Menu 3D Sonar X-PRESS MenuHighlight Split Position on the 3D Sonar X-Press Menu 3D Lower Range Beam Sensitivity3D Bottom Zoom 3D History Reset 3D ViewTo adjust the 3D History To Reset 3D ViewNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuSkip Next Waypoint Save Current TrackClear Current Track Save Current RouteRemove Grid Cancel NavigationRemove Target 3D Frame Style Sonar Menu TAB2D Sonar Colors 3D Bottom StyleTo set Fish ID+ 2D Beam SelectFish ID+ To change Beam SelectFish ID Sensitivity To change the Fish ID Sensitivity settingTo change the RTS Window setting To change the Fish ID 3D Reference settingDepth Lines Bottom ViewZoom Width KHZ SensitivityNoise Filter To change the Noise Filter settingTo change the Max Depth setting Surface ClutterColor BAR Temperature GraphWater Type Waypoints Navigation Menu TABTracks North Reference To change the Chart Orientation settingTo change the North Reference setting RoutesMAP Datum Trolling Grid RotationTrackpoint Interval Track MIN DistanceTo Export All Navigation Data Chart Menu TABExport ALL NAV Data Delete ALL NAV DataSpot Soundings Chart Detail LevelMAP Borders LAT/LON GridClear MAP Offset Shaded DepthSET MAP Offset To change the Depth Alarm setting Alarms Menu TABDepth Alarm Fish ID AlarmOFF Course Alarm LOW Battery AlarmTemp Alarm Alarm Tone Arrival AlarmDrift Alarm Units Depth Setup Menu TABTo change the Units Depth setting To change the Units Temp settingLanguage User ModeUnits Distance Units SpeedSelect Readouts Triplog ResetRestore Defaults To Select Readouts Default Sonar View Customized Sonar ViewDaylight Saving Time Depth OffsetTemp Offset Local Time ZoneNmea Output Position FormatTime Format Date FormatTo turn Sonar on or off SonarViews Menu TAB To turn Nmea Output on or offSeries Doesn’t Power Up Accessories Menu TABTroubleshooting Series Defaults to Simulator with a Transducer Attached Control head loses power at high speeds Display ProblemsBoat’s engine Finding the Cause of NoiseOther electronic devices Noise re-appearsHumminbird Service Policy Year Limited WarrantyFor IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Operating Frequency SpecificationsAppendix a Contact Humminbird