Humminbird 531374-1_A manual No Access Under Mounting Location

Page 25

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:53..coPM Pagem25

NO ACCESS UNDER MOUNTING LOCATION

Follow these steps to deck mount the GPS receiver in a situation where you must route the cable to the side because there is no space for a cable underneath the mounting location.

1.Determine the best location, then test route the cable from the mounting location to the control head.

NOTE: AS-EC10 10' extension cables are available from Humminbird® if your planned routing exceeds 20', (6 m). Maximum cable length, including extensions, should not exceed 50' (16 m).

2.Confirm the cable length is good and route the cable from the receiver to the control head. If holes are required to route the cable, they must be 3/4" (19 mm) to allow for the cable connector. Secure the NMEA pigtail with electrical tape.

NOTE: Remember to caulk or seal screw holes and drilled holes as needed to protect your boat from water damage.

3.The GPS receiver has two wire routing notches. Use the cable notch closest to the intended cable route.

4.With the cable routed, position the GPS receiver in the planned mounting location and mark the mounting holes with a pencil or punch.

5.Move the GPS receiver to the side and drill the two 9/64" (3.5 mm) pilot holes.

6.Align the GPS receiver's screw holes over the pilot screw holes and attach with the #8 - 1 1/4" Phillips head screws. Hand tighten only!

FINISH ROUTING THE CABLE AND CHECK

GPS RECEIVER OPERATION

After installing a GPS receiver, you should perform the following procedure to finish routing the GPS cable to the control head and to check to make sure that the control head is working correctly.

1.Secure the cable along its path to the control head as needed with cable ties.

2.Plug in the GPS receiver cable into the Communications port on the control head. See Testing the System Installation to use the System Status start-up option and/or the GPS Diagnostic View to confirm a good installation.

1 2 3 4

1Power

	2	Temperature
	3	Communications
	4	Transducer	5
	5	Cable Collector Insert	5
	5	Cable Collector Insert

20

Image 25

Contents Page Thank You Table of Contents 2D Sonar X-Press Menu Menu System Start-Up Options Menu3D Sonar X-Press Menu Navigation X-Press MenuAlarms Menu Tab Chart Menu TabSetup Menu Tab Views Menu Tab Accessories Menu Tab TroubleshootingHOW the 900 Series Works Series Introduction3D Sonar 2D SonarMULTI-MEDIA Card MMC SD Slot GPS and CartographySD Slot Installation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurationsBasic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Screws provided Plug Cable Connector Assembly to Back of Control HeadIN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer InstallationTo determine transducer mounting location Transom Transducer InstallationStepped Hull To attach the pivot to the transducer To mount the transducer bracket to the boatBut do not completely tighten Attaching the BracketTo adjust the running position of the transducer To mount the transducer pivot assembly to the bracketNormal Cavitation Reassemble To route the transom transducer cableFully tightened Routing the CableTrial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Transducer Mounted Inside the HullTrolling Motor Transducer Installation Test and Finish the Transducer InstallationIf you have… Then use GPS Receiver InstallationHand-tighten only Follow these steps to stem mount the GPS receiverAccess Under Mounting Location Access Under Mounting LocationTo the cable as shown Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationRouting the cable to the control head Install the temperature probe accessoryTo test the installation Testing the System InstallationSeries 947c 3D Combo Title Screen Powering UP the Control HeadTriplog WHAT’S on the 3D Sonar DisplayBait Ball RTS Real Time Sonar Window WHAT’S on the 2D Sonar DisplayBottom Presentation Real Time Sonar RTS WindowKEY Functions POWER/LIGHT KEYView KEY Menu KEYWAY Cursor Control KEY View Preset KeysExit KEY Info KEYViews MARK/GOTO KEYViews available on your 900 Series are 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View2D Zoom View 2D Zoom ViewBIRD’S EYE View Beam Sonar ViewBeam Sonar View Bird’s Eye ViewChart View CHART/BIRD’S EYE Combo ViewChart/Bird’s Eye Combo View with Active Cursor Chart View with Active CursorCHART/2D Combo View CHART/3D Combo ViewChart/2D Combo View Chart View with Cursor Present Chart OrientationViewing Cartography Navigation WAYPOINTS, Routes and TracksWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Navigate to a Waypoint or Position Chart View with TargetADD a Waypoint Target or Trolling Grid SAVE, Edit or Delete a Route Chart View with GridEDIT, Delete or Hide Saved Tracks Save or Clear a Current TrackMenu System Sonar Tab, Advanced Mode Sonar Tab, Normal ModeSTART-UP Options Menu Exit Normal operation by powering your 900 Series offNormal Operation Normal Simulator System StatusSimulator Self Test Accessory Test GPS Diagnostic ViewSystem Status Self TestGPS Diagnostic View Accessory TestAccessory Test Screen GPS Diagnostic View2D Sonar X-PRESS Menu To Adjust Split Screen PositionActive Side Split PositionTo adjust the Upper Range To adjust the SensitivitySensitivity Upper RangeLower Range Chart SpeedBottom Lock Bottom Range To adjust the Bottom Range2D/3D Priority To change the 2D/3D PriorityHighlight Split Position on the 3D Sonar X-Press Menu 3D Sonar X-PRESS Menu3D Sonar X-Press Menu 3D Bottom Zoom Beam Sensitivity3D Lower Range To adjust the 3D History Reset 3D ViewTo Reset 3D View 3D HistoryNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuClear Current Track Save Current TrackSave Current Route Skip Next WaypointRemove Target Cancel NavigationRemove Grid 2D Sonar Colors Sonar Menu TAB3D Bottom Style 3D Frame StyleFish ID+ 2D Beam SelectTo change Beam Select To set Fish ID+To change the RTS Window setting To change the Fish ID Sensitivity settingTo change the Fish ID 3D Reference setting Fish ID SensitivityZoom Width Bottom ViewKHZ Sensitivity Depth LinesTo change the Max Depth setting To change the Noise Filter settingSurface Clutter Noise FilterWater Type Temperature GraphColor BAR Tracks Navigation Menu TABWaypoints To change the North Reference setting To change the Chart Orientation settingRoutes North ReferenceTrackpoint Interval Trolling Grid RotationTrack MIN Distance MAP DatumExport ALL NAV Data Chart Menu TABDelete ALL NAV Data To Export All Navigation DataMAP Borders Chart Detail LevelLAT/LON Grid Spot SoundingsSET MAP Offset Shaded DepthClear MAP Offset Depth Alarm Alarms Menu TABFish ID Alarm To change the Depth Alarm settingTemp Alarm LOW Battery AlarmOFF Course Alarm Drift Alarm Arrival AlarmAlarm Tone To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units DepthUnits Distance User ModeUnits Speed LanguageRestore Defaults Triplog ResetSelect Readouts To Select Readouts Default Sonar View Customized Sonar ViewTemp Offset Depth OffsetLocal Time Zone Daylight Saving TimeTime Format Position FormatDate Format Nmea OutputViews Menu TAB SonarTo turn Nmea Output on or off To turn Sonar on or offTroubleshooting Accessories Menu TABSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Control head loses power at high speeds Display ProblemsOther electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engineHumminbird Service Policy Year Limited WarrantySeries Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Operating Frequency SpecificationsAppendix a Contact Humminbird