Humminbird 531374-1_A Surface Clutter, Noise Filter, MAX Depth, To change the Max Depth setting

Page 65

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:54..coPM Pagem65

SURFACE CLUTTER

(Advanced)

Surface Clutter adjusts the filter that removes surface clutter noise caused by algae and aeration. The lower the setting, the less surface clutter will be displayed. The Surface Clutter menu choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).

 

To change the Surface Clutter setting:

 

1. Make sure you are in Advanced User Mode, then

 

highlight Surface Clutter on the Sonar main menu.

 

2. Use the LEFT or RIGHT 4-WAY Cursor Control

 

keys to change the Surface Clutter setting.

 

(Low = 1 to High = 10, Default = 5)

Surface Clutter

 

NOISE FILTER

(Advanced)

Noise Filter adjusts the sonar Noise Filter to limit interference on the display from sources such as your boat engine, turbulence, or other sonar devices. The Noise Filter menu choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).

NOTE: The Off setting removes all filtering; Low, Medium and High settings add progressive filtering of the sonar returns. In some deep water situations, the High setting may actually make it harder for the control head to find the bottom.

To change the Noise Filter setting:

1.Make sure you are in Advanced User Mode, then highlight Noise Filter on the Sonar main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Noise Filter setting. (Off, Low, Medium, High, Default = Off)

MAX DEPTH

(Advanced)

Max Depth adjusts the maximum depth of 2D operation. The performance of your 900 series™ can be tuned to the maximum depth you will be fishing in by setting the Max Depth. When a maximum depth is set, your 900 series™ will not attempt to acquire sonar data below that depth, thus increasing overall performance. When Max Depth is set to Auto, the 900 series™ will acquire bottom readings as needed (within the capacity of the unit). If the bottom is deeper than the Max Depth setting, the digital depth readout will flash, indicating that the 900 series™ cannot locate the bottom. The Max Depth menu choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode).

To change the Max Depth setting:

1.Make sure you are in Advanced User Mode and in a 2D Sonar View, then highlight Max Depth on the Sonar main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Max Depth setting. (AUTO, 10 to 1000 feet, 3 to 330 meters [International Models Only], Default = AUTO)

60

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Page Thank You Table of Contents 2D Sonar X-Press Menu Menu System Start-Up Options Menu3D Sonar X-Press Menu Navigation X-Press MenuAlarms Menu Tab Chart Menu TabSetup Menu Tab Views Menu Tab Accessories Menu Tab TroubleshootingHOW the 900 Series Works Series Introduction3D Sonar 2D SonarSD Slot GPS and CartographyMULTI-MEDIA Card MMC SD Slot Installation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurationsGimbal Mounting the Control Head Control Head InstallationBasic installation tasks that you must perform include Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Screws provided Plug Cable Connector Assembly to Back of Control HeadIN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer InstallationStepped Hull Transom Transducer InstallationTo determine transducer mounting location To attach the pivot to the transducer To mount the transducer bracket to the boatBut do not completely tighten Attaching the BracketNormal Cavitation To mount the transducer pivot assembly to the bracketTo adjust the running position of the transducer Reassemble To route the transom transducer cableFully tightened Routing the CableDetermine the transducer mounting location Inside the Hull Transducer InstallationTrial installation Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Transducer Mounted Inside the HullTrolling Motor Transducer Installation Test and Finish the Transducer InstallationIf you have… Then use GPS Receiver InstallationHand-tighten only Follow these steps to stem mount the GPS receiverTo the cable as shown Access Under Mounting LocationAccess Under Mounting Location Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationRouting the cable to the control head Install the temperature probe accessoryTo test the installation Testing the System InstallationSeries 947c 3D Combo Title Screen Powering UP the Control HeadTriplog WHAT’S on the 3D Sonar DisplayBait Ball RTS Real Time Sonar Window WHAT’S on the 2D Sonar DisplayBottom Presentation Real Time Sonar RTS WindowKEY Functions POWER/LIGHT KEYView KEY Menu KEYWAY Cursor Control KEY View Preset KeysExit KEY Info KEYViews available on your 900 Series are MARK/GOTO KEYViews 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View2D Zoom View 2D Zoom ViewBIRD’S EYE View Beam Sonar ViewBeam Sonar View Bird’s Eye ViewChart View CHART/BIRD’S EYE Combo ViewChart/Bird’s Eye Combo View with Active Cursor Chart View with Active CursorChart/2D Combo View CHART/3D Combo ViewCHART/2D Combo View Viewing Cartography Chart OrientationChart View with Cursor Present Waypoints, Routes and Tracks WAYPOINTS, Routes and TracksNavigation SAVE, EDIT, or Delete a Waypoint ADD a Waypoint Target or Trolling Grid Chart View with TargetNavigate to a Waypoint or Position SAVE, Edit or Delete a Route Chart View with GridMenu System Save or Clear a Current TrackEDIT, Delete or Hide Saved Tracks Sonar Tab, Advanced Mode Sonar Tab, Normal ModeSTART-UP Options Menu Exit Normal operation by powering your 900 Series offNormal Operation Normal Simulator System StatusSimulator Self Test Accessory Test GPS Diagnostic ViewSystem Status Self TestGPS Diagnostic View Accessory TestAccessory Test Screen GPS Diagnostic View2D Sonar X-PRESS Menu To Adjust Split Screen PositionActive Side Split PositionTo adjust the Upper Range To adjust the SensitivitySensitivity Upper RangeBottom Lock Chart SpeedLower Range Bottom Range To adjust the Bottom Range2D/3D Priority To change the 2D/3D Priority3D Sonar X-Press Menu 3D Sonar X-PRESS MenuHighlight Split Position on the 3D Sonar X-Press Menu 3D Lower Range Beam Sensitivity3D Bottom Zoom To adjust the 3D History Reset 3D ViewTo Reset 3D View 3D HistoryNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuClear Current Track Save Current TrackSave Current Route Skip Next WaypointRemove Grid Cancel NavigationRemove Target 2D Sonar Colors Sonar Menu TAB3D Bottom Style 3D Frame StyleFish ID+ 2D Beam SelectTo change Beam Select To set Fish ID+To change the RTS Window setting To change the Fish ID Sensitivity settingTo change the Fish ID 3D Reference setting Fish ID SensitivityZoom Width Bottom ViewKHZ Sensitivity Depth LinesTo change the Max Depth setting To change the Noise Filter settingSurface Clutter Noise FilterColor BAR Temperature GraphWater Type Waypoints Navigation Menu TABTracks To change the North Reference setting To change the Chart Orientation settingRoutes North ReferenceTrackpoint Interval Trolling Grid RotationTrack MIN Distance MAP DatumExport ALL NAV Data Chart Menu TABDelete ALL NAV Data To Export All Navigation DataMAP Borders Chart Detail LevelLAT/LON Grid Spot SoundingsClear MAP Offset Shaded DepthSET MAP Offset Depth Alarm Alarms Menu TABFish ID Alarm To change the Depth Alarm settingOFF Course Alarm LOW Battery AlarmTemp Alarm Alarm Tone Arrival AlarmDrift Alarm To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units DepthUnits Distance User ModeUnits Speed LanguageSelect Readouts Triplog ResetRestore Defaults To Select Readouts Default Sonar View Customized Sonar ViewTemp Offset Depth OffsetLocal Time Zone Daylight Saving TimeTime Format Position FormatDate Format Nmea OutputViews Menu TAB SonarTo turn Nmea Output on or off To turn Sonar on or offSeries Doesn’t Power Up Accessories Menu TABTroubleshooting Series Defaults to Simulator with a Transducer Attached Control head loses power at high speeds Display ProblemsOther electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engineHumminbird Service Policy Year Limited WarrantyFor IN-WARRANTY service, complete the following steps Returning Your Unit for ServiceSeries Accessories Operating Frequency SpecificationsAppendix a Contact Humminbird
Top Page Image Contents