Humminbird 531374-1_A manual Simulator, System Status, Self Test

Page 49

www531374..reelsche-1 A - 947 Man.qxd 2/15/2005matic7:53..coPM Pagem49

SIMULATOR

Use the Simulator to learn how to use your 900 Series™ before taking your boat on the water. The Simulator is a very powerful tool that simulates on-the-water operation, providing a randomly-updated display. We recommend going through this manual while using the Simulator, since all of the menus function and affect the display the way they actually do when in Normal operation.

Simulator

NOTE: To get the full benefit of the Simulator, it is important to select Simulator manually from the Start-Up Options menu as opposed to letting the 900 Series™ enter Simulator automatically (as it will if a transducer is not connected and you do nothing during power up). Manually selecting Simulator from the Start-Up Options menu allows you to pre- configure your 900 Series™ for on-the-water operation. Any menu changes you make will be saved for later use.

A Simulation message will appear on the display periodically to remind you that you are using the Simulator.

Exit the Simulator by powering your 900 Series™ off.

SYSTEM STATUS

Use System Status to view system connections and to conduct a unit self-test. Exit System Status by powering your 900 Series™ off.

The following screens are displayed in turn when you press the VIEW button when using System Status:

•Self Test

•Accessory Test

•GPS Diagnostic View.

SELF TEST

Self Test displays results from the internal diagnostic self test, including unit serial number, Printed Circuit Board (PCB) serial number, software revision, total hours of operation and the input voltage.

Self Test Screen

44

Image 49

Contents Page Thank You Table of Contents 2D Sonar X-Press Menu Menu System Start-Up Options Menu3D Sonar X-Press Menu Navigation X-Press MenuAlarms Menu Tab Chart Menu TabSetup Menu Tab Views Menu Tab Accessories Menu Tab TroubleshootingHOW the 900 Series Works Series Introduction3D Sonar 2D SonarMULTI-MEDIA Card MMC SD Slot GPS and CartographySD Slot Installation Overview Accessory BUSAccessory Bus 900 Series has a wide variety of configurationsBasic installation tasks that you must perform include Control Head InstallationGimbal Mounting the Control Head Mounting Screws Washer Gimbal Mounting Bracket Cables Routed Near Mounting Bracket Screws provided Plug Cable Connector Assembly to Back of Control HeadIN-DASH Mounting the Control Head Plug Cable Connector Assembly to Back of Control Head Connecting the Control Head Power Cable to the Boat Transducer InstallationTo determine transducer mounting location Transom Transducer InstallationStepped Hull To attach the pivot to the transducer To mount the transducer bracket to the boatBut do not completely tighten Attaching the BracketTo adjust the running position of the transducer To mount the transducer pivot assembly to the bracketNormal Cavitation Reassemble To route the transom transducer cableFully tightened Routing the CableTrial installation Inside the Hull Transducer InstallationDetermine the transducer mounting location Route the cable Permanently mount the transducerMake sure the position of the transducer is marked Transducer Mounted Inside the HullTrolling Motor Transducer Installation Test and Finish the Transducer InstallationIf you have… Then use GPS Receiver InstallationHand-tighten only Follow these steps to stem mount the GPS receiverAccess Under Mounting Location Access Under Mounting LocationTo the cable as shown Finish Routing the Cable and Check GPS Receiver Operation No Access Under Mounting LocationRouting the cable to the control head Install the temperature probe accessoryTo test the installation Testing the System InstallationSeries 947c 3D Combo Title Screen Powering UP the Control HeadTriplog WHAT’S on the 3D Sonar DisplayBait Ball RTS Real Time Sonar Window WHAT’S on the 2D Sonar DisplayBottom Presentation Real Time Sonar RTS WindowKEY Functions POWER/LIGHT KEYView KEY Menu KEYWAY Cursor Control KEY View Preset KeysExit KEY Info KEYViews MARK/GOTO KEYViews available on your 900 Series are 3D/2D Combo View Views and Readouts3D/2D Combo View 2D Sonar View 2D Sonar View2D Zoom View 2D Zoom ViewBIRD’S EYE View Beam Sonar ViewBeam Sonar View Bird’s Eye ViewChart View CHART/BIRD’S EYE Combo ViewChart/Bird’s Eye Combo View with Active Cursor Chart View with Active CursorCHART/2D Combo View CHART/3D Combo ViewChart/2D Combo View Chart View with Cursor Present Chart OrientationViewing Cartography Navigation WAYPOINTS, Routes and TracksWaypoints, Routes and Tracks SAVE, EDIT, or Delete a Waypoint Navigate to a Waypoint or Position Chart View with TargetADD a Waypoint Target or Trolling Grid SAVE, Edit or Delete a Route Chart View with GridEDIT, Delete or Hide Saved Tracks Save or Clear a Current TrackMenu System Sonar Tab, Advanced Mode Sonar Tab, Normal ModeSTART-UP Options Menu Exit Normal operation by powering your 900 Series offNormal Operation Normal Simulator System StatusSimulator Self Test Accessory Test GPS Diagnostic ViewSystem Status Self TestGPS Diagnostic View Accessory TestAccessory Test Screen GPS Diagnostic View2D Sonar X-PRESS Menu To Adjust Split Screen PositionActive Side Split PositionTo adjust the Upper Range To adjust the SensitivitySensitivity Upper RangeLower Range Chart SpeedBottom Lock Bottom Range To adjust the Bottom Range2D/3D Priority To change the 2D/3D PriorityHighlight Split Position on the 3D Sonar X-Press Menu 3D Sonar X-PRESS Menu3D Sonar X-Press Menu 3D Bottom Zoom Beam Sensitivity3D Lower Range To adjust the 3D History Reset 3D ViewTo Reset 3D View 3D HistoryNavigation X-Press Menu Highlight Split Position on the Navigation X-Press MenuClear Current Track Save Current TrackSave Current Route Skip Next WaypointRemove Target Cancel NavigationRemove Grid 2D Sonar Colors Sonar Menu TAB3D Bottom Style 3D Frame StyleFish ID+ 2D Beam SelectTo change Beam Select To set Fish ID+To change the RTS Window setting To change the Fish ID Sensitivity settingTo change the Fish ID 3D Reference setting Fish ID SensitivityZoom Width Bottom ViewKHZ Sensitivity Depth LinesTo change the Max Depth setting To change the Noise Filter settingSurface Clutter Noise FilterWater Type Temperature GraphColor BAR Tracks Navigation Menu TABWaypoints To change the North Reference setting To change the Chart Orientation settingRoutes North ReferenceTrackpoint Interval Trolling Grid RotationTrack MIN Distance MAP DatumExport ALL NAV Data Chart Menu TABDelete ALL NAV Data To Export All Navigation DataMAP Borders Chart Detail LevelLAT/LON Grid Spot SoundingsSET MAP Offset Shaded DepthClear MAP Offset Depth Alarm Alarms Menu TABFish ID Alarm To change the Depth Alarm settingTemp Alarm LOW Battery AlarmOFF Course Alarm Drift Alarm Arrival AlarmAlarm Tone To change the Units Depth setting Setup Menu TABTo change the Units Temp setting Units DepthUnits Distance User ModeUnits Speed LanguageRestore Defaults Triplog ResetSelect Readouts To Select Readouts Default Sonar View Customized Sonar ViewTemp Offset Depth OffsetLocal Time Zone Daylight Saving TimeTime Format Position FormatDate Format Nmea OutputViews Menu TAB SonarTo turn Nmea Output on or off To turn Sonar on or offTroubleshooting Accessories Menu TABSeries Doesn’t Power Up Series Defaults to Simulator with a Transducer Attached Control head loses power at high speeds Display ProblemsOther electronic devices Finding the Cause of NoiseNoise re-appears Boat’s engineHumminbird Service Policy Year Limited WarrantySeries Accessories Returning Your Unit for ServiceFor IN-WARRANTY service, complete the following steps Operating Frequency SpecificationsAppendix a Contact Humminbird