Pioneer GM-6400F owner manual Installation Before installing the amplifier

Page 13

Installation

Before installing the amplifier

WARNING

!To ensure proper installation, use the supplied parts in the manner specified. If any parts other than those supplied are used, they may damage internal parts of the amplifier, or be- come loose causing the amplifier to shut down.

!Do not install in:

—Places where it could injure the driver or passengers if the vehicle stops suddenly.

—Places where it may interfere with the dri- ver, such as on the floor in front of the dri- ver’s seat.

!Install tapping screws in such a way that the screw tip does not touch any wire. This is im- portant to prevent wires from being cut by vi- bration of the car, which can result in fire.

!Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-circuit.

!When drilling to install the amplifier, always confirm no parts are behind the panel and protect all cables and important equipment (e.g. fuel/brake lines, wiring) from damage.

CAUTION

!To ensure proper heat dissipation of the ampli- fier, ensure the following during installation:

—Allow adequate space above the amplifier for proper ventilation.

—Do not cover the amplifier with a floor mat or carpet.

!Avoid routing wires through hot areas, such as near the heater outlet. Heat may damage the insulation, resulting in a short-circuit through the vehicle body.

!The optimal installation location differs de- pending on the car model. Secure the ampli- fier at a sufficiently rigid location.

!Firstly make temporary connections and check to ensure the amplifier and system op- erate properly.

Section

04

!

After installing the amplifier, confirm that the

English

 

 

spare tire, jack and tools can be easily re-

 

 

moved.

 

Example of installation on the floor mat or chassis

1Place the amplifier in the desired instal- lation location.

Insert the supplied tapping screws (4 mm ×

18mm) into the screw holes and push on the screws with a screwdriver so they make an im- print where the installation holes are to be lo- cated.

2Drill 2.5 mm (1/8 inch) diameter holes at the imprints either on the carpet or di- rectly on the chassis.

3Install the amplifier with the use of supplied tapping screws (4 mm × 18 mm).

1Tapping-screws (4 mm × 18 mm)

2Drill a 2.5 mm (1/8 inch) diameter hole

3Floor mat or chassis

En 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents GM-6400F Contents Before you start After-sales service for Pioneer productsInformation to User Visit our websiteBefore you start Before connecting/ installing the amplifier Setting gain properly Setting the Unit What’s whatSetting the Unit Before connecting the amplifier Connecting the units Connection diagramFuse 25 a × Fuse 30 a × Grommet Rear side Front sideAbout bridged mode Connecting the unitsAbout suitable specification of speaker Connecting the speakersEnglish Connections when using the speaker input wire Connecting the power terminal Connecting the speaker output terminals Example of installation on the floor mat or chassis Installation Before installing the amplifierCEA2006 Specifications Additional information SpecificationsTable des matières Parleurs InstallationAvant de connecter ’installer l’amplificateur Service après-vente des produits PioneerAvant de commencer Visitez notre site WebPrécaution Réglage correct du gain 02 Réglage de l’appareil Description de l’appareilRéglage de l’appareil Avant de connecter l’amplificateur Connexion des appareils Schéma de connexionConnexion des appareils Propos du mode pontéPropos de la spécification adaptée du haut-parleurs De l’antenne, du câble d’antenne et du syntoniseurHaut-parleur autre que le haut-parleur d’extrêmes graves Connexion des haut-parleursSortie B du haut-parleur Sortie trois canaux Sortie deux canaux mono Haut-parleur mono Connexions lors de l’utilisation du jack d’entrée RCAPercez un trou de 14 mm dans la carrosse- rie du véhicule Connexion de la borne d’alimentationConnexion des bornes de sortie des haut-parleurs Fil de la télécommande du système26 Fr Exemple d’installation sur le tapis de sol ou le châssis Installation Avant d’installer l’amplificateurCule Installation Caractéristiques CEA2006 Informations complémentaires Caractéristiques techniquesAntes de comenzar Servicio posventa para productos Pioneer ContenidoServicio posventa para productos Pioneer Antes de comenzarVisite nuestro sitio Web Antes de conectar/instalar el amplificadorPrecaución Configuración correcta de la ganancia Configuración de la unidad Qué es cada cosaNectado Configuración de la unidad Antes de conectar el amplificador Conexión de las unidades Diagrama de conexiónAcerca del modo en puente Conexión de las unidadesAcerca de una especificación adecuada del altavoz Aparte del altavoz de subgraves Conexión de altavocesSalida de tres canales Conexiones al utilizar el cable de entrada del altavoz Conexiones al utilizar una toma de entrada RCAConexión del terminal de potencia 40 Es Conexión de las unidades Ejemplo de instalación en la alfombra o chasis Instalación Antes de instalar el amplificadorNo cubra el amplificador con una alfombra o moqueta Después de instalar el amplificador, confirmeInstalación Especificaciones CEA2006 Información adicional EspecificacionesKnazx 08H00000 Pioneer Corporation

GM-6400F specifications

The Pioneer GM-6400F is a versatile four-channel power amplifier designed to provide a significant boost in sound quality and performance for car audio systems. This robust amplifier is engineered to enhance your listening experience by delivering clear and powerful audio reproduction.

One of the main features of the GM-6400F is its impressive power output. With a maximum power of up to 640 watts, this amplifier is capable of driving multiple speakers without distortion, ensuring that every note and beat is delivered with precision. The GM-6400F can deliver 75 watts RMS per channel at 4 ohms, making it suitable for a wide variety of speakers, and produces a punchy and dynamic sound that can fill any vehicle.

Additionally, the amplifier incorporates advanced Class D technology, which contributes to its efficiency and compact size. Class D amplifiers are known for generating less heat compared to traditional Class AB amplifiers, allowing the GM-6400F to utilize a smaller chassis without sacrificing power or performance. This enables easier installation in tight spaces without compromising sound quality.

The GM-6400F also features a built-in low-pass filter that allows users to tailor the sound to their preference. This filter can be adjusted to focus on specific frequencies, making it easier to blend with subwoofers or enhance specific elements of the audio mix. Furthermore, the amplifier provides a variable bass boost which can add extra thump to low frequencies for those who desire a more pronounced bass experience.

With its durable construction, the Pioneer GM-6400F is built to endure the rough conditions of a mobile environment. The amplifier’s sleek design ensures not just performance but also aesthetic appeal, making it a great addition to any audio setup. An easy-to-read LED indicator on the front panel helps monitor the amplifier’s status without the need for complex diagnostics.

Overall, the Pioneer GM-6400F is an exceptional choice for car audio enthusiasts seeking a powerful yet efficient amplifier. Its combination of advanced technology, user-friendly features, and robust build quality makes it a top contender for enhancing sound in any vehicle audio system. Whether you’re listening to your favorite music or experiencing cinematic sound effects, the GM-6400F is designed to elevate your auditory experience on the road.
Top Page Image Contents