Icom IC-FR3000 Before Entering the Adjustment Mode, Process to the Permit Adjustment Mode Access

Page 17

■BEFORE ENTERING THE ADJUSTMENT MODE

CAUTION!: Need to back up the original memory data using CS-FR3000 before cloning the adjustment frequencies.

When program the adjustment frequencies into the repeater, the repeater’s memories channels will be overwritten the data and deleted original memory data at the same time.

Need to do cloning “Adjustment Mode Access” permitting and adjustment frequency into the CPU using CS-FR3000 before entering the adjustment mode. Otherwise, the repeater can not enter the adjustment mode.

■PROCESS TO THE PERMIT “ADJUSTMENT MODE ACCESS”

1 Run the CS-FR3000 CLONING SOFTWARE.

2 Open the “Common Setting” folder .

3 Click the “Expert” card on the tree view window.

4 Double-click somewhere on the Common setting screen window, then appear the “Edit Expert” window. 5 Click the “Expert 2” tab, then click the “Adjustment Mode Access” check box.

6 Click “OK” button.

7 Click the “Memory CH” card on the tree view window.

8 Input adjustment frequencies as following page 4-4.

9 Cloning to the repeater then the repeater can be enter the adjustment mode. Show the next page to enter the adjustment mode.

4

55

2

3

6

MEMORY CHANNEL SCREEN (Sample only)

4 - 2

Image 17

Contents IC-fr3000 iC-fr3 1 0 Repair Notes IntroductionOrdering Parts Table of Contents General SpecificationsPA Unit Board LayoutBottom view Logic UnitRX Unit TX UnitRF Circuit RX Unit Receiver Circuits2 1ST Mixer and 1ST if Circuits RX Unit 3 2ND if and Demodulator Circuits RX UnitMIC Mute Transmitter CircuitsReceiver Mute Circuits Logic Unit Case of the Dtmf Signals from Dialer IC Case of the 2/5TONE SignalsCase of the Ctcss and Dtcs Signals From the CPU Power Amplifier Circuit PA UnitPLL Circuits Other Circuits Power Supply CircuitsExpander IC Logic Unit IC39 Port AllocationsExpander IC Logic Unit IC40 Expander IC Logic Unit IC415 D/A Converter IC TX Unit IC5 TEL DtcsiBusy MCKPreparation Battery RXRequired Test Equipment MICProcess to the Permit Adjustment Mode Access Before Entering the Adjustment ModeOperating in the Adjustment Mode Entering the Adjustment ModeExiting the Adjustment Mode After Finishing AdjustmentExplanation of LCD Display in the Adjustment Mode Adjustment Mode CH ListWide NarrowIC-FR3000 TOP View PLL AdjustmentTX Unit TOP View RX Unit TOP View CP2 CP4Software Adjustment Output PowerLOW DeviationDtcs CtcssREG Unit Section Parts ListLogic Unit Front UnitBridge Resistor ERJ12YJ390U ECEV1CA100SR ECEV1CA220SR Tantalum Teesva 1V 104M8L RX Unit Tantalum Teesva 1V 224M8L Rvco Unit TX Unit Tvco Unit PA Unit JACK1 Unit VR UnitChassis Unit JACK2 UnitOption Unit Installation Duplexer and isolater installation Example 2 Duplexer Connection Connection Example 1 Isolater ConnectionExample 3 Duplexer and Isolater Connection ISO Isolater DUP DuplexerMechanical Parts and Disassembly Front Unit REG Unit Rvco Unit Transistors and Fets SEMI-CONDUCTOR InformationDiodes Tvco Unit Rvco Unit Front Unit¡BOTTOM View Rvco Unit Tvco Unit VR UnitBoard Logic UnitGND TMUTE1 Txaf Tone TMUTE2 Patemp Rvswr Fwswr RX Unit RX Unit TX Unit TX Unit PA Unit PA Unit REG Unit JACK1 Unit REG UnitJACK2 Unit Block Diagram PA Unit Wiring Diagram Section Voltage Diagram Rvco Unit TX Unit PA Unit Unit Logic Unit Chassis Unit Icom New Zealand 32, Kamiminami, Hirano-ku, Osaka, 547-0003, Japan