Furuno Ls4100 manual Nav window

Page 25

NAV DATA-1,-2:Choose the number of navigation data items to display on the nav data displays, from two, three or four items. Requires appropriate nav data.

WATER TYPE: Choose the water type with which to use the LS-4100, from Salt or Fresh.

KEY BEEP: Turn key beep on or off.

BATT VOLTAGE: Turn the battery voltage indication (appears at the top right corner on the screen) on or off. When on it replaces the picture advance speed indication.

Page 2

NAV DISPLAY: Choose the nav data to display in the nav data window at the top left-hand corner. You may choose from temperature/speed, latitude/longitude, range and bearing, course over ground, trip distance or wind speed. Requires appropriate nav data.

40.7° F 16.2kt

Nav window

NMEA0183: Choose NMEA version of navigator; Ver. 1.5, Ver. 2.0 or Ver. 3.0.

TLL OUTPUT: Enables/disables output of TLL (Target Latitude, Longitude) position when the [MARK] key is operated. “TLL” outputs latitude and longitude position. “FURUNO-TLL,” available with connection of navigator that can output FURUNO TLL, outputs latitude and longitude, water temperature, depth, etc.

BEARING: Ship’s course and bearing to a waypoint may be displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth’s magnetic deviation. Requires bearing data.

WIND SPD/DIR: Choose the wind speed and direction reference from true and apparent. Requires wind sensor. Apparent: The direction (in relation to ship’s bow) and speed of the wind as it appears to those on board, relative to the speed and direction of the boat; combination of the true wind and the wind caused by the boat's movement. True: The speed and direction (in relation to ship’s bow) of the wind felt or measured when stationary.

TRIP SOURCE: Choose speed source for the trip distance indication; Own (transducer with speed sensor or separate speed sensor) or NMEA.

TEMP SOURCE: Choose source of water temperature input; Off, Own (transducer with water temperature sensor or separate temperature sensor), or NMEA.

SPEED SOURCE: Choose source of speed input; Off, Own (transducer with speed sensor or separate speed sensor), or NMEA. Requires speed data.

TEMP CALIB.: If the water temperature sensor-generated water temperature indication is wrong, you can correct it here, when “Own” is selected as temperature source. For example, if the water temperature indication is 2° higher than actual water temperature, enter -2. The setting range is -40°F to +40°F.

19

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Echo Soundr Table of Contents Safety Instructions Safety Instructions for the Installer Foreword FeaturesWord to LS-4100 Owners IiiSystem Overview System configurationEquipment lists Standard supplyHow to remove the hard cover Power On/OffOperation Control DescriptionBrilliance/contrast adjustment window Adjusting Display Contrast, BrillianceMode selection window Choosing a Display, FrequencyDual frequency display Single frequency displayMarker-zoom display 50 kHzBottom-lock display Bottom-zoom displayNav data displays Bottom-zoom displayAutomatic Operation Menu Operating ProcedureHow automatic operation works Choosing automatic operationManual Operation Choosing the manual modeRange offset Gain offsetShifting the range Adjusting the gainMeasuring Depth How to measure depth with the VRMChoosing Picture Advance Speed Picture advance options windowSuppressing Low Level Noise Suppressing InterferenceForms of interference Clutter appearanceScope Display Erasing Weak EchoesAppearance of weak echoes Scope displayAlarm description AlarmsActivating an alarm Alarm menuWaypoints Depth, temperature, speed setting WindowSilencing the buzzer Fish level optionsRegistering waypoint by L/L Registering a waypoint on the screenKHz display Waypoint data displayEditing waypoints Setting destination waypointErasing waypoints Waypoint listNAV Data Setup window Setting Up Nav Data DisplaysNav data window and item displayable Nav data display-1NAV data display-2 Other Menu ItemsHUE Picture Color Deep Gain How white line worksSystem Menu Water temperature display wide, FSystem Menu System menusNav window Page MAINTENANCE, Troubleshooting Diagnostics TroubleshootingTroubleshooting table Installation menuTest Pattern Memory ClearClear memory display Test patternsDisplay Unit InstallationThru-hull Mount Transducer Typical thru-hull mount transducer installations Thru-hull mount transducer dimensionsAcceptable transducer mounting locations Suitable transducer mounting locationsTransom Mount Transducer Installing the 520-5PWD on a flat hullTransducer preparation 520-5PWDInstalling the 525-5PWD Installing the transom mount transducer on a deep-V hull525-5PWD Inside-hull Transducer Optional Triducer Pre-test for speed and temperatureFinal preparation Triducer 525ST-MSDMounting location Installation of bracketHeight required at mounting location Mounting location on single drive boatSensor position and transom angle AdjustingAttaching the sensor to the bracket Vertical adjustment and cable routingAttaching the sensor to the bracket Cable routingOptional Water Temperature/Speed Sensor Establishing the ground Power connectorOptional equipment Water temp/speed sensor IEC 61162-1 Data SentencesNmea PORT, Nmea MIX Installation MenuBottom level display Waas options windowSpecifications of Echo Sounder LS-4100 Page Page Display Unit 00014698000
Top Page Image Contents