Furuno Ls4100 manual IEC 61162-1 Data Sentences, Water temp/speed sensor

Page 41

Water temp/speed sensor

Connect the optional water temp/speed sensor to the XDR connector with the optional converter connector (Type 02S4147) as shown below.

Connect to XDR port at rear of display unit

MJ-A10SPF

Input data sentences (con’t)

Sentence	Meaning
MWV	Wind speed and
	angle
RMA	Recommended
	minimum specific
	LORAN-C data
RMB	Recommended
	minimum navigation
	information
RMC	Recommended
	minimum specific
	GPS/TRANSIT data

MJ-A6SRMD

Tape connectors with

vulcaninzing tape and then vinyl tape to waterproof them. Bind tape ends with cable ties to prevent

From tape from unraveling. sensor

MJ-A10SRMD

From transducer

	VHW	Water speed and
		heading
	VTG	Course over ground
		and ground speed
	XTE	Cross track error
	Output data sentences

	Sentence	Meaning

Connection of converter

connector 02S4147

4.8IEC 61162-1 Data Sentences

The tables below show the data sentences which can be input to and output from the LS-4100. The transmission speed for both input and output is 4800 bps. Data is output at two-second intervals.

Input data sentences

Sentence	Meaning
BWC	Bearing and distance to
	waypoint
GGA	Global positioning system
	(GPS) fix data
GLL	Geographic position -
	latitude/longitude
HDG	Heading, deviation and variation
HDT	Heading, true
MDA	Atmospheric pressure
MTW	Water temperature

DBT (Ver. 1.5)	Depth below
	transducer
DPT (Ver. 2.0, Ver.	Depth
3.0)
MTW*	Water temperature
RMB* (Ver. 2.0)	Recommended
	minimum
	navigation
	information
VHW*	Water speed and
	heading
TLL*	Target position,
	output by [MARK]
	key.

*= Available with connection of optional sensors/navaid

35

Image 41

Contents Echo Soundr Table of Contents Safety Instructions Safety Instructions for the Installer Foreword FeaturesWord to LS-4100 Owners IiiSystem Overview System configurationEquipment lists Standard supplyHow to remove the hard cover Power On/OffOperation Control DescriptionBrilliance/contrast adjustment window Adjusting Display Contrast, BrillianceMode selection window Choosing a Display, FrequencyDual frequency display Single frequency displayMarker-zoom display 50 kHzBottom-lock display Bottom-zoom displayNav data displays Bottom-zoom displayAutomatic Operation Menu Operating ProcedureHow automatic operation works Choosing automatic operationManual Operation Choosing the manual modeRange offset Gain offsetShifting the range Adjusting the gainMeasuring Depth How to measure depth with the VRMChoosing Picture Advance Speed Picture advance options windowSuppressing Low Level Noise Suppressing InterferenceForms of interference Clutter appearanceScope Display Erasing Weak EchoesAppearance of weak echoes Scope displayAlarm description AlarmsActivating an alarm Alarm menuWaypoints Depth, temperature, speed setting WindowSilencing the buzzer Fish level optionsRegistering waypoint by L/L Registering a waypoint on the screenKHz display Waypoint data displayEditing waypoints Setting destination waypointErasing waypoints Waypoint listNAV Data Setup window Setting Up Nav Data DisplaysNav data window and item displayable Nav data display-1HUE Picture Color Other Menu ItemsNAV data display-2 Deep Gain How white line worksSystem Menu Water temperature display wide, FSystem Menu System menusNav window Page MAINTENANCE, Troubleshooting Diagnostics TroubleshootingTroubleshooting table Installation menuTest Pattern Memory ClearClear memory display Test patternsThru-hull Mount Transducer InstallationDisplay Unit Typical thru-hull mount transducer installations Thru-hull mount transducer dimensionsAcceptable transducer mounting locations Suitable transducer mounting locationsTransom Mount Transducer Installing the 520-5PWD on a flat hullTransducer preparation 520-5PWD525-5PWD Installing the transom mount transducer on a deep-V hullInstalling the 525-5PWD Inside-hull Transducer Optional Triducer Pre-test for speed and temperatureFinal preparation Triducer 525ST-MSDMounting location Installation of bracketHeight required at mounting location Mounting location on single drive boatSensor position and transom angle AdjustingAttaching the sensor to the bracket Vertical adjustment and cable routingAttaching the sensor to the bracket Cable routingOptional Water Temperature/Speed Sensor Optional equipment Power connectorEstablishing the ground Water temp/speed sensor IEC 61162-1 Data SentencesNmea PORT, Nmea MIX Installation MenuBottom level display Waas options windowSpecifications of Echo Sounder LS-4100 Page Page Display Unit 00014698000