Furuno Ls4100 manual Operation, Control Description, Power On/Off, Display unit

Page 7

1. OPERATION

1.1 Control Description

Cursor Pad

Selects menu items; shifts VRM.

MENU

MODE

ESC

GAIN

RANGE

MARK

ECHO SOUNDER POWER

LS-4100 BRILL

Selects display mode.

Opens/closes menu; escapes from current operation.

Adjusts gain.

Selects basic display range.

Outputs L/L position to external equipment; registers selected position as waypoint.

Long press: Turns power on/off.

Momentary press: Adjusts display contrast and brilliance.

Display unit

How to remove the hard cover

Place your thumbs at the center of the cover, and then lift the cover while pressing it with your thumbs.

1.2 Power On/Off

Press the [POWER/BRILL] key more than one second to turn on the power. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation and displays program number. (If “NG” (No Good) appears, try to press any key except the [POWER/BRILL] key to start operation. However, the equipment may not work properly. Contact your dealer.) You may

press any key after the completion of the equipment check to start operation sooner.

1

Image 7

Contents Echo Soundr Table of Contents Safety Instructions Safety Instructions for the Installer Iii FeaturesForeword Word to LS-4100 OwnersStandard supply System configurationSystem Overview Equipment listsControl Description Power On/OffHow to remove the hard cover OperationChoosing a Display, Frequency Adjusting Display Contrast, BrillianceBrilliance/contrast adjustment window Mode selection window50 kHz Single frequency displayDual frequency display Marker-zoom displayBottom-zoom display Bottom-zoom displayBottom-lock display Nav data displaysChoosing automatic operation Menu Operating ProcedureAutomatic Operation How automatic operation worksGain offset Choosing the manual modeManual Operation Range offsetShifting the range Adjusting the gainPicture advance options window How to measure depth with the VRMMeasuring Depth Choosing Picture Advance SpeedClutter appearance Suppressing InterferenceSuppressing Low Level Noise Forms of interferenceScope display Erasing Weak EchoesScope Display Appearance of weak echoesAlarm menu AlarmsAlarm description Activating an alarmFish level options Depth, temperature, speed setting WindowWaypoints Silencing the buzzerWaypoint data display Registering a waypoint on the screenRegistering waypoint by L/L KHz displayWaypoint list Setting destination waypointEditing waypoints Erasing waypointsNav data display-1 Setting Up Nav Data DisplaysNAV Data Setup window Nav data window and item displayableNAV data display-2 Other Menu ItemsHUE Picture Color Deep Gain How white line worksSystem menus Water temperature display wide, FSystem Menu System MenuNav window Page MAINTENANCE, Troubleshooting Installation menu TroubleshootingDiagnostics Troubleshooting tableTest patterns Memory ClearTest Pattern Clear memory displayDisplay Unit InstallationThru-hull Mount Transducer Suitable transducer mounting locations Thru-hull mount transducer dimensionsTypical thru-hull mount transducer installations Acceptable transducer mounting locations520-5PWD Installing the 520-5PWD on a flat hullTransom Mount Transducer Transducer preparationInstalling the 525-5PWD Installing the transom mount transducer on a deep-V hull525-5PWD Inside-hull Transducer Triducer 525ST-MSD Pre-test for speed and temperatureOptional Triducer Final preparationMounting location on single drive boat Installation of bracketMounting location Height required at mounting locationSensor position and transom angle AdjustingCable routing Vertical adjustment and cable routingAttaching the sensor to the bracket Attaching the sensor to the bracketOptional Water Temperature/Speed Sensor Establishing the ground Power connectorOptional equipment Water temp/speed sensor IEC 61162-1 Data SentencesNmea PORT, Nmea MIX Installation MenuBottom level display Waas options windowSpecifications of Echo Sounder LS-4100 Page Page Display Unit 00014698000