Furuno Ls4100 manual Installation Menu, Nmea PORT, Nmea MIX

Page 42

4.9 Installation Menu

The installation menu mainly contains items which are set at installation.

1.Turn on the power while pressing the [MENU/ESC] key. Continue pressing the [MENU/ESC] key until the Installation menu appears.

Installation Menu

SIMULATION On

TEST ...

LCD PATTERN ...

MEMORY CLEAR

NMEA PORT	: In/Out
NMEA MIX	: Off
GPS WAAS*	: Off

SET BOTTOM LEVEL ..

*= Setting cannot be changed when NMEA PORT setting is "IN/IN."

Installation menu

SIMULATION: The simulation mode provides, without connection of the transducer, simulated operation of the equipment, using internally generated echoes. All controls are operative. The message “SIM” appears at the top right corner on the screen when the simulation mode is active.

1.At the installation menu, press ► to open the simulation mode options window.

2.Press ▼ to choose “On” to turn on the simulation mode.

3.Press the [POWER/BRILL] key about three seconds to turn off the power.

4.Press the [POWER/BRILL] key to turn on the power. “SIM” appears at the top right corner of the display.

5.To turn off the simulation mode, select Off at step 2.

NMEA port setup

(NMEA PORT, NMEA MIX)

The POWER port can function as an input port or input/output port. Change the setting to “In/In” when connecting GP-310B/320B and a wind sensor.

When connecting the GP-310B/320B and a wind sensor, first turn on “GPS WAAS” (in the Installation menu) and then select “In/In” as the NMEA port setting.

1.Turn on the power while pressing and holding down the [MENU/ESC] key. Continue pressing the [MENU/ESC] key until the Installation menu appears.

2.Choose NMEA PORT, and then press ► to display the NMEA port options window.

3.Use ▲ or ▼ to choose In/Out or In/In as appropriate.

In/Out: Input and Output (default setting)

In/In: Input only (Available with connection of the GP-310B/320B and a wind sensor.)

4.Press ◄, choose NMEA MIX, and then press ► to display the NMEA MIX options window.

5.Use ▲ or ▼ to choose Off or On. Choose On to output input data.

Off: Outputs the data sentences of LS-4100 only.

On: Outputs the data sentences of LS-4100 and sentences which are input from other equipment.

6.To restore normal operation, turn off the power and then turn it on again.

36

Image 42

Contents Echo Soundr Table of Contents Safety Instructions Safety Instructions for the Installer Word to LS-4100 Owners FeaturesForeword IiiEquipment lists System configurationSystem Overview Standard supplyOperation Power On/OffHow to remove the hard cover Control DescriptionMode selection window Adjusting Display Contrast, BrillianceBrilliance/contrast adjustment window Choosing a Display, FrequencyMarker-zoom display Single frequency displayDual frequency display 50 kHzNav data displays Bottom-zoom displayBottom-lock display Bottom-zoom displayHow automatic operation works Menu Operating ProcedureAutomatic Operation Choosing automatic operationRange offset Choosing the manual modeManual Operation Gain offsetAdjusting the gain Shifting the rangeChoosing Picture Advance Speed How to measure depth with the VRMMeasuring Depth Picture advance options windowForms of interference Suppressing InterferenceSuppressing Low Level Noise Clutter appearanceAppearance of weak echoes Erasing Weak EchoesScope Display Scope displayActivating an alarm AlarmsAlarm description Alarm menuSilencing the buzzer Depth, temperature, speed setting WindowWaypoints Fish level optionsKHz display Registering a waypoint on the screenRegistering waypoint by L/L Waypoint data displayErasing waypoints Setting destination waypointEditing waypoints Waypoint listNav data window and item displayable Setting Up Nav Data DisplaysNAV Data Setup window Nav data display-1Other Menu Items NAV data display-2HUE Picture Color How white line works Deep GainSystem Menu Water temperature display wide, FSystem Menu System menusNav window Page MAINTENANCE, Troubleshooting Troubleshooting table TroubleshootingDiagnostics Installation menuClear memory display Memory ClearTest Pattern Test patternsInstallation Display UnitThru-hull Mount Transducer Acceptable transducer mounting locations Thru-hull mount transducer dimensionsTypical thru-hull mount transducer installations Suitable transducer mounting locationsTransducer preparation Installing the 520-5PWD on a flat hullTransom Mount Transducer 520-5PWDInstalling the transom mount transducer on a deep-V hull Installing the 525-5PWD525-5PWD Inside-hull Transducer Final preparation Pre-test for speed and temperatureOptional Triducer Triducer 525ST-MSDHeight required at mounting location Installation of bracketMounting location Mounting location on single drive boatAdjusting Sensor position and transom angleAttaching the sensor to the bracket Vertical adjustment and cable routingAttaching the sensor to the bracket Cable routingOptional Water Temperature/Speed Sensor Power connector Establishing the groundOptional equipment IEC 61162-1 Data Sentences Water temp/speed sensorInstallation Menu Nmea PORT, Nmea MIXWaas options window Bottom level displaySpecifications of Echo Sounder LS-4100 Page Page Display Unit 00014698000