Multiquip manual Components, MT55F Rammer

Page 12

COMPONENTS

Figure 1. MT55F Rammer

Figure 1 shows the location of the controls and components for the MT55F Tamping Rammer.The functions of each control is described below:

1.Throttle Lever –Used to adjust engine speed (rpm). Move lever forward (SLOW) to reduce engine speed, move lever back toward operator (FAST) to increase speed.

2.Fuel Shut-OffValve – Supplies fuel from the fuel tank to the engine.To begin fuel flow move the fuel shut-off valve downward.

3.Oil Bath Fill Plug – Open this plug to add oil to the oil bath reservoir.

4.Drain Valve – Open this valve to remove oil from the bellows.

5. Primary Air Cleaner – Pre-cleans (first stage) dirt and other debris from entering the engine.

6.Foot– Laminated wood with tempered steel plate for superior shock absorption.

7.Oil Level Sight Glass – Indicates the level of oil in the oil bath reservoir.

8.FuelTank/Cap – Remove this cap to add unleaded gaso- line to the fuel tank.Make sure cap is tightened securely.DO NOT over fill.

CAUTION - Fueling The Engine

Adding fuel to the tank should be done only when the engine is stopped and has had an opportunity to cool down. In the event of a fuel spill, DO NOT attempt to start the engine until the fuel residue has been completely wiped up,

9.Bellows – Reservoir for oil bath.

10.Handle – To operate rammer GRIP handle assembly firmly on both sides.

11.Nameplate– Displaysinformationregardingtherammer.

12.Engine Air Cleaner – Prevents dirt (second stage) and other debris form entering the engine.

13.Muffler – Used to reduce noise and emissions.

PAGE 12 — MT55F RAMMER — OPERATION AND PARTS MANUAL — REV. #5 (01/06/12)

Image 12

Contents Model MT55F Proposition 65 Warning MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Table of Contents MT55F Tamping RammerParts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesGeneral Safety Engine Safety Transporting Safety General Information Definition of Tamping RammerSpecifications MT-55F Rammer SpecificationsComponents MT55F RammerBasic Engine Initial ServicingOperation Rammer Gearbox and Spring Cylinder Oil BathMotor Oil Grade 16 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Normal Shutdown Maintenance DailyMT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Troubleshooting Engine TroubleshootingRammer Troubleshooting Sample Parts List Explanation of Codes in the Remarks ColumnSuggested Spare Parts MT55F Rammer 3TO 5 Units with RobinTo start, switch must be in the on position Nameplate and DecalsPart Name QTY Remarks Crankcase and Engine Assy Part Name QTY Remarks 28 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Stiffener Guide Cylinder Assy Part Name QTY Foot ASSY. Option Part Name QTY Remarks Tank and Handle Assy Throttle Body 36 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Fuel Cock ASSY. N18L-02 Robin EH-090D Engine Crankcase Assy Valve Guide Robin EH-090D Engine Crankshaft and Piston Assy Spacer T=0.8 Robin EH-090D Engine Intake and Exhaust Assy PIN Spring Robin EH-090D Engine Governor Assy Governor Lever Robin EH-090D Engine Recoil Starter Assy Blower Housing CP Robin EH-090D Engine Carburetor Assy Throttle Valve Robin EH-090D Engine Electric Device Assy Flywheel CP Robin EH-092D Engine Crankcase Assy Ball BEARING, 60074C3 Robin EH-092D Engine Crankshaft and Piston Assy Crankshaft CP Robin EH-092D Engine Intake and Exhaust Assy Gasket Exhaust Robin EH-092D Engine Carburetor Assy Lever SUB ASSY. Throttle Robin EH-092D Engine AIR Cleaner Assy Part Name Robin EH-092D Engine GOVERNOR, Operation Assy Linkage Bushing Robin EH-092D Engine Blower Housing Assy Label Robin EH-092D Engine Recoil Starter Assy Slide PLATE, B Robin EH-092D Engine Accessories Assy Accessory Tool KIT Terms and Conditions of Sale Parts Freight PolicyMT55F Rammer Operation and Parts Manual REV. #5 01/06/12 HERE’S HOW to GET Help