Multiquip MT55F manual Normal Shutdown

Page 17

OPERATION

CAUTION -Throttle Lever

Make sure that the throttle lever is moved to the FULL OPEN position. Operating the rammer at less than full speeds can result in damage to the clutch springs or foot

2.TheMT55FTampingrammerisdesignedtorunat3,600rpm. At optimum rpm the foot hits at the rate between 600 ~ 695 impacts per minute. Increasing throttle speed past factory setrpmdoesnotincreaseimpactsand maydamageunit.The MT55F is designed to advance while tamping. For faster advance, pull back slightly on the handle so that rear of foot contactssoil first.

Figure 13. Throttle Lever (Idle)

2.Aftertheenginecools,turntheenginestart/stopswitchtothe “OFF” position (Figure 14).

Figure 14. ON/OFF Switch (Off Position)

2.Closethe fuelshut-offvalve(Figure15)bymovingthefuel cock lever to the CLOSED position.

Stopping The Engine

Normal Shutdown

1.Move throttle lever quickly from the FULL OPEN to IDLE position (Figure 13) and run the engine for three minutes at low speed.

Figure 15. Fuel Shut-OFF Valve (Off Position)

Emergency Showdown

1.Move the throttle lever quickly to the IDLE position, and turn the engine start/stop switch to the OFF position. Turn fuel valve lever to the CLOSED position.

MT55F RAMMER — OPERATION AND PARTS MANUAL — REV. #5 (01/06/12) — PAGE 17

Image 17

Contents Model MT55F Proposition 65 Warning MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 MT55F Tamping Rammer Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Messages Safety InformationGeneral Safety Engine Safety Transporting Safety Definition of Tamping Rammer General InformationMT-55F Rammer Specifications SpecificationsMT55F Rammer ComponentsInitial Servicing Basic EngineRammer Gearbox and Spring Cylinder Oil Bath OperationMotor Oil Grade 16 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Normal Shutdown Daily MaintenanceMT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Engine Troubleshooting TroubleshootingRammer Troubleshooting Explanation of Codes in the Remarks Column Sample Parts ListMT55F Rammer 3TO 5 Units with Robin Suggested Spare PartsNameplate and Decals To start, switch must be in the on positionPart Name QTY Remarks Crankcase and Engine Assy Part Name QTY Remarks 28 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Stiffener Guide Cylinder Assy Part Name QTY Foot ASSY. Option Part Name QTY Remarks Tank and Handle Assy Throttle Body 36 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Fuel Cock ASSY. N18L-02 Robin EH-090D Engine Crankcase Assy Valve Guide Robin EH-090D Engine Crankshaft and Piston Assy Spacer T=0.8 Robin EH-090D Engine Intake and Exhaust Assy PIN Spring Robin EH-090D Engine Governor Assy Governor Lever Robin EH-090D Engine Recoil Starter Assy Blower Housing CP Robin EH-090D Engine Carburetor Assy Throttle Valve Robin EH-090D Engine Electric Device Assy Flywheel CP Robin EH-092D Engine Crankcase Assy Ball BEARING, 60074C3 Robin EH-092D Engine Crankshaft and Piston Assy Crankshaft CP Robin EH-092D Engine Intake and Exhaust Assy Gasket Exhaust Robin EH-092D Engine Carburetor Assy Lever SUB ASSY. Throttle Robin EH-092D Engine AIR Cleaner Assy Part Name Robin EH-092D Engine GOVERNOR, Operation Assy Linkage Bushing Robin EH-092D Engine Blower Housing Assy Label Robin EH-092D Engine Recoil Starter Assy Slide PLATE, B Robin EH-092D Engine Accessories Assy Accessory Tool KIT Freight Policy Terms and Conditions of Sale PartsMT55F Rammer Operation and Parts Manual REV. #5 01/06/12 HERE’S HOW to GET Help