Multiquip MT55F manual Operation, Rammer Gearbox and Spring Cylinder Oil Bath

Page 14

OPERATION

This section is intended to assist the operator with the initial start-up of the MT55FTamping Rammer.It extremely important that this section be read carefully before attempting to operate the rammer.

DO NOT use your rammer until this section is thoroughly understood.

CAUTION - Read Manual

DO NOT attempt to operate the Tamping Rammer until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood.

Rammer Gearbox and Spring Cylinder Oil Bath

This unit uses an oil bath lubrication system.Perform the following:

1.Check the oil level through the oil level sight glass (Figure 3) at the rear of the tamper foot.

Fuel

1.Fill the fuel tank (Figure 4) with unleaded gasoline. DONOT overfill, wipe up spilled fuel immediately.

Figure 4. Fuel Tank

Engine Oil Check

1.To check the engine oil level, place the rammer on secure level ground with the engine stopped.

2.Remove the filler cap/dipstick from the engine oil filler hole (Figure 5) and wipe it clean.

Figure 3. Foot Housing Sight Glass

2.If oil is not visible, add 10W-30 SE, SF or higher grade motor oil into the oil fill plug opening (Figure 3).The bath contains approximately 1.0 pints (520 cc.)

NOTE

The oil level should be kept at the half

way point of the sight glass.

 

Figure 5. Engine Oil Dipstick

3.Insertandremovethedipstickwithoutscrewingitintothefiller neck. Check the oil level shown on the dipstick.

4.If the oil level is low (Figure 6), fill to the edge of the oil filler hole with the recommended oil type (Table 3).Maximum oil capacity is .079 gallons (0.3 liters)

PAGE 14 — MT55F RAMMER — OPERATION AND PARTS MANUAL — REV. #5 (01/06/12)

Image 14
Contents Model MT55F Proposition 65 Warning MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Table of Contents MT55F Tamping RammerParts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesGeneral Safety Engine Safety Transporting Safety General Information Definition of Tamping RammerSpecifications MT-55F Rammer SpecificationsComponents MT55F RammerBasic Engine Initial ServicingOperation Rammer Gearbox and Spring Cylinder Oil BathMotor Oil Grade 16 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Normal Shutdown Maintenance DailyMT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Troubleshooting Engine TroubleshootingRammer Troubleshooting Sample Parts List Explanation of Codes in the Remarks ColumnSuggested Spare Parts MT55F Rammer 3TO 5 Units with RobinTo start, switch must be in the on position Nameplate and DecalsPart Name QTY Remarks Crankcase and Engine Assy Part Name QTY Remarks 28 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Stiffener Guide Cylinder Assy Part Name QTY Foot ASSY. Option Part Name QTY Remarks Tank and Handle Assy Throttle Body 36 MT55F Rammer Operation and Parts Manual REV. #5 01/06/12 Fuel Cock ASSY. N18L-02 Robin EH-090D Engine Crankcase Assy Valve Guide Robin EH-090D Engine Crankshaft and Piston Assy Spacer T=0.8 Robin EH-090D Engine Intake and Exhaust Assy PIN Spring Robin EH-090D Engine Governor Assy Governor Lever Robin EH-090D Engine Recoil Starter Assy Blower Housing CP Robin EH-090D Engine Carburetor Assy Throttle Valve Robin EH-090D Engine Electric Device Assy Flywheel CP Robin EH-092D Engine Crankcase Assy Ball BEARING, 60074C3 Robin EH-092D Engine Crankshaft and Piston Assy Crankshaft CP Robin EH-092D Engine Intake and Exhaust Assy Gasket Exhaust Robin EH-092D Engine Carburetor Assy Lever SUB ASSY. Throttle Robin EH-092D Engine AIR Cleaner Assy Part Name Robin EH-092D Engine GOVERNOR, Operation Assy Linkage Bushing Robin EH-092D Engine Blower Housing Assy Label Robin EH-092D Engine Recoil Starter Assy Slide PLATE, B Robin EH-092D Engine Accessories Assy Accessory Tool KIT Terms and Conditions of Sale Parts Freight PolicyMT55F Rammer Operation and Parts Manual REV. #5 01/06/12 HERE’S HOW to GET Help