Baja Marine 405 manual After Fueling Checklist

Page 51

Section 5 • Fuel System

Electrical equipment, including blowers – power off.

Doors, hatches – closed.

Smoking material – extinguished.

Inboard tanks – grounded.

Filler pipe – marked GAS or DIESEL.

Fuel nozzle – in contact with filler pipe to prevent static sparks.

Fill level – fill less than rated capacity of tank; allow for fuel expansion.

Trim – fuel weight distributed equally.

D.After Fueling – Checklist:

Doors, hatches – open.

Sniff test – if fuel fumes remain, operate blowers until fumes are gone.

Fuel tank – secure filler cap.

Spills – wipe; dispose of rags ashore.

Fuel Fill Location

(Fig. 5.3.1)

Fuel Tank Opening

Fuel Fill Cap

405 Performance®

5.3

Image 51
Contents Performance Baja MarineFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Service, Parts and Repair for Your Boat Hull Identification Number HINManufacturer’s Certification About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Labels SafetyLegally Mandated Minimum Required Equipment Fire Extinguishing SystemCarbon Monoxide Carbon Monoxide Monitor Lifesaving Equipment Impaired Operation Additional Recommended Equipment for Safe OperationUnited States Power CapacityLoad Capacity PropellersMaintain Control StabilityChart Your Course WeatherGeneral Considerations Water Sports SwimmingSkiing General Emergency SituationsFlooding, Swamping and Capsizing Medical EmergencyWater Rescue FirePropulsion, Control or Steering Failure Safety HotlinesCollisions and Leaking GroundingInternational Requirements Environmental ConsiderationsFuel and Oil Spillage Waste Disposal Wake/WashExcessive Noise Nautical Terms Key to Symbols on Controls & Prints Baja Marine Corp This Page Intentionally Left Blank Docking /Lifting /Trailering Passenger Locations General Boat Arrangement2 Hull Propulsion System Basic Boat Dimensions and Clearances MetricGeneral Deck Layout FIG General Deck LayoutPower Trim Unit and Gauge Description of Major ControlsGear Shift and Throttle Control Trim Tabs Trailer SwitchTachometer and Hour Meter Ignition Shutdown SwitchEngine Alarm System Important GaugesNavigation and Anchor Lights Oil Pressure, Water Temperature, Voltmeter and Fuel GaugesPre-Launch, Launch and Post- Launch Checklist Using Your BoatFueling the Boat Trailer Launching and LoadingPersonal Flotation Devices BoardingStarting the Engine Passenger Instruction and LocationStopping the Engine Shifting to Drive the BoatHydraulic Steering Steering SystemsPower Steering System Power SteeringThis page intentionally left blank Drain Plug Bilge & Underwater GearBilge Fuel & Oil SpillageVibration and Causes Maintenance and ServiceEngines and Stern Drive Bilge BlowersImpact to Stern Drive Propeller Removal and InstallationGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Fueling Precautions Before and During Fueling ChecklistStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Batteries Electrical SystemsElectrical Systems Direct Current DCElectrolytic Corrosion & Zinc Anodes Breakers and/or FusesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Ignition Switch Drive Pump with K-Plane Trim Tabs FIG Switch Panel Wire Information FIG Fuse Panel Wire Diagram FIG VOlT 60hz DC Main Distribution Panel Wiring Diagram FIG This Page Intentionally Left Blank Options & Accessories Locations Options & AccessoriesAutomatic Fire Extinguisher System Option Fire Extinguisher PortCanvas Horn Canvas Care and MaintenanceSwim Platform w/ Ladder Optional Depth Finder OptionalRequirements for Operators Stereo SystemHead Systems Portable Head with Pump-OutVent Filter Exhaust SystemsVacuFlush Head Option Holding Tank OperationThis page intentionally left blank Required Inspection, Service Maintenance Summary Guide for Inspection, Service and MaintenanceInterval Interval Summary Guide For Inspection, Service and MaintenanceUseful Service Information Bilge Area Inspection, Service and Maintenance ProtocolBoat Storage Winterization Checklist for Boats Stored on LandBatteryies Topside and SuppliesMiscellaneous Fitting Out After StorageFuel Systems Fuel SystemSecurity Considerations Power Steering System MaintenanceQuick Reference Checklist Boarding the Boat GeneralBoat Systems Starting the Engine Returning to Port General Quick Reference Checklist cont’d Departing GeneralQuick Reference Checklist cont’d Securing the BoatIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Fiberglass & Gelcoat Paint Cleaning Agents & Other SubstancesCare & Refinishing Stains & ScratchesCanvas and Clear Vinyl Permanently Moored or Docked BoatsTopside Areas Acrylic Plastic Sheeting Plastic GlassInterior Upholstery Fabric Exterior Upholstery FabricThis Page Intentionally Left Blank Index Index Performance