Baja Marine 30 manual Exhaust Systems, VacuFlush Head Option, Holding Tank Operation, Vent Filter

Page 64

Section 7 • Options & Accessories

C.VacuFlush® Head (Option)

The VacuFlush® head utilizes a HEAD SYSTEM breaker on the main distribution panel. The foot pedal at the base of the toilet opens a mechanical seal and vacuum forces waste through the opening in the bowl to an accumulator tank, through the vacuum pump and then to the holding tank or treatment tank (See Figure 7.5.1).

Typical VacuFlush® with Holding Tank,

Dockside Pump-Out & Macerator (Fig. 7.5.1)

dockside pump-out

Thru-Hull

Vent

Vent filter

head

vacu-generatordischarge seacock)

 

holding tank

head

Macerator

(optional)

 

To Operate:

1.Turn ON the WATER PUMP breaker.

2.Turn ON the HEAD SYSTEM breaker.

REFER TO OWNER’S MANUAL PACKET FOR INSTRUCTIONS AND WARRANTY INFORMATION.

D. Holding Tank Operation

Waste from the head is directed into the holding tank located in the engine room. The holding tank fluid level indicator is located on the main distribution panel or in the head which indicates 3/4 FULL, FULL and DO NOT FLUSH, or on some models may read Full, 1/2, or Empty. When the FULL light is on, the DO NOT FLUSH light will also be on. When these lights are ON, the holding tank must be emptied before the head can be reused.

E.Vent Filter

The vent filter is designed to control odors associated with the head system operations. The vent filter is located on the holding tank. The filter must be changed at the beginning of each boating season to be effective. The vent filter is installed in-line on the holding tank ventilation hose.

Note: Do not over fill the holding tank as this will flood the vent filter and render it useless. Filter replacement will then be required. See Parts Manual for correct replacement filter.

10.Exhaust Systems

Your boat comes with a choice of different exhaust systems. Below is a description of the standard and optional systems on your 30 Outlaw.

Thru-Hub Exhaust (standard): Thru-hub exhaust propellers consist of a round barrel to which the blades are attached. The exhaust passes through the barrel and out the back, without making contact with the blades. This provides a good clean water flow to the blades, usually resulting in good acceleration and hole shot.

CorsaTM Performance Quick & Quiet II (option): A full time, non-switchable, thru-hull exhaust system that uses patented Silencer Tips with a pair of upper exhaust splitters connected to the lower wishbone and the exhaust riser.

CorsaTM Performance Quick & Quiet Plus (option): An electronically operated exhaust diverter used in conjunction with the same Silencer Tips of the Quick & Quiet II system, but with the added flexibility to switch the exhaust flow to fully silenced, thru-prop operation. The switch is used to change the exhaust exits, either thru-prop or thru- hull, which will provide maximum performance or minimum exhaust sound.

Many areas regulate noise limits. Even if there are no laws, courtesy demands that boats operate quietly.

30 Outlaw®

7.5

Image 64
Contents Baja Marine OutlawFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction HIN Number Hull Identification Number HINAbout Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsFire Extinguishing System Legally Mandated Minimum Required EquipmentCarbon Monoxide Carbon Monoxide Monitor Lifesaving Equipment Additional Recommended Equipment for Safe Operation Impaired OperationPower Capacity Load CapacityPropellers United StatesStability Maintain ControlWeather Chart Your CourseGeneral Considerations Swimming Water SportsSkiing Emergency Situations GeneralMedical Emergency Water RescueFire Flooding, Swamping and CapsizingSafety Hotlines Collisions and LeakingGrounding Propulsion, Control or Steering FailureEnvironmental Considerations International RequirementsFuel and Oil Spillage Wake/Wash Waste DisposalExcessive Noise Nautical Terms Key to Symbols on Controls & Prints This Page Intentionally Left Blank Baja Marine Corp This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger Locations2 Hull Basic Boat Dimensions and Clearances Metric Propulsion SystemGeneral Deck Layout Description of Major Controls Power Trim Unit and GaugeGear Shift and Throttle Control Trailer Switch Trim TabsIgnition Shutdown Switch Engine Alarm SystemImportant Gauges Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EngineSteering Systems Power SteeringHydraulic Steering Bilge & Underwater Gear BilgeFuel & Oil Spillage Drain PlugMaintenance and Service Engines and Stern DriveBilge Blowers Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Before and During Fueling Checklist Fueling PrecautionsStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Electrical Systems Electrical SystemsDirect Current DC BatteriesBreakers and/or Fuses Electrolytic Corrosion & Zinc AnodesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Drive Pump Drive Pump w/ K-Plane Trim Tabs Ignition Switch Switch Panel Wire Information FIG This Page Intentionally Left Blank Options & Accessories Options & Accessories LocationsFire Extinguisher Port Automatic Fire Extinguisher System OptionCanvas Canvas Care and Maintenance Swim Platform w/ Ladder OptionalDepth Finder Optional HornStereo System Head SystemsPortable Head with Pump-Out Requirements for OperatorsExhaust Systems VacuFlush Head OptionHolding Tank Operation Vent FilterSummary Guide for Inspection, Service and Maintenance Required Inspection, Service MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaWinterization Checklist for Boats Stored on Land BatteryiesTopside and Supplies Boat StorageFitting Out After Storage Fuel SystemsFuel System MiscellaneousPower Steering System Maintenance Security ConsiderationsBoarding the Boat General Quick Reference ChecklistBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralSecuring the Boat Quick Reference Checklist cont’dIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Paint Cleaning Agents & Other Substances Care & RefinishingStains & Scratches Fiberglass & GelcoatPermanently Moored or Docked Boats Topside AreasAcrylic Plastic Sheeting Plastic Glass Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Outlaw