Baja Marine 275 manual Permanently Moored or Docked Boats, Topside Areas, Canvas and Clear Vinyl

Page 83

Section 9 • Care & Refinishing

Minor scratches and deeper stains that do not penetrate the gelcoat may be removed by light sanding and buffing.

4.Permanently Moored or Docked Boats

If permanently moored in salt water or fresh water, your boat will collect marine growth on its bottom. This will detract from the boat’s beauty and greatly affect its performance. There are two methods of preventing this:

Periodically haul the boat out of the water and scrub the bottom with a bristle brush and a solution of soap and water.

Paint the hull below the waterline with a good grade of antifouling paint. DO NOT paint the engine drive surfaces.

NOTE: There are EPA regulations regarding bottom paint application. Consult your Baja® dealer for proper application methods.

5.Topside Areas

A.Stainless Steel and Alloy Fittings

6.Acrylic Plastic Sheeting (Plastic Glass)

Never use a dry cloth or duster or glass cleaning solutions on acrylic.

To clean acrylic, first flood it with water to wash off as much dirt as possible. Next, use your bare hand, with plenty of water, to feel and dislodge any caked dirt or mud. A soft, grit-free cloth may then be used with a nonabrasive soap or detergent. A soft sponge, kept clean for this purpose, is excellent. Blot dry with a clean damp chamois.

Grease and oil may be removed from acrylic with kerosene, hexane, white (not aviation or ethyl) gasoline or aliphatic naphtha (no aromatic content).

Do not use solvents such as acetone, silicone spray, benzine, carbon tetrachloride, fire extinguisher fluid, dry cleaning fluid or lacquer thinner on acrylic, since they attack the surface.

Remove fine scratches with fine automotive acrylic rubbing and polishing compounds.

Stainless steel and alloy fittings should be cleaned with soap and water or household glass cleaner. Remove rust spots as soon as possible with a brass, silver or chrome cleaner. Irreversible pitting will develop under rust that remains for any period of time. Never use an abrasive like sandpaper or steel wool on stainless. These may actually cause rust. To help protect the stainless, we recommend the use of a good car wax.

B.Salt Crystals

When instruments are exposed to a saltwater environment, salt crystals may form on the bezel and the plastic covers. These salt crystals should be removed with a soft, damp cloth; never use abrasives or rough, dirty cloths to wipe plastic parts. Mild household detergents or plastic cleaners can be used to keep the instruments bright and clean.

Refer to the Owner’s Manual Packet for instructions and warranty information.

7.Canvas and Clear Vinyl

Do not fold or store any of the canvas pieces while wet. All canvas should be rolled or folded when dry and stored in a clean, dry place. For clear vinyl pieces, the recommended methods for storage are rolling or laying down flat. The clear vinyl should never be folded or creased as cracking will result. To protect the clear vinyl from rubbing against itself while rolled or stored flat, place a piece of very soft, nonabrasive cloth between the pieces. If the surface of the clear vinyl becomes scratched, the canvas manufacturer has provided a canvas care sheet located in your Owner’s Manual Packet. When storing the rear (aft) curtain, fold the canvas over the clear vinyl window (do not fold clear vinyl), then roll or store flat. Refer to the canvas care instructions in the Owner’s Manual Packet.

9.2

275 Performance®

Image 83
Contents Performance Baja MarineFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Manufacturer’s Certification Service, Parts and Repair for Your BoatHull Identification Number HIN About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Labels SafetyCarbon Monoxide Legally Mandated Minimum Required EquipmentFire Extinguishing System Carbon Monoxide Monitor Lifesaving Equipment Impaired Operation Additional Recommended Equipment for Safe OperationUnited States Power CapacityLoad Capacity PropellersMaintain Control StabilityGeneral Considerations Chart Your CourseWeather Skiing Water SportsSwimming General Emergency SituationsFlooding, Swamping and Capsizing Medical EmergencyWater Rescue FirePropulsion, Control or Steering Failure Safety HotlinesCollisions and Leaking GroundingFuel and Oil Spillage International RequirementsEnvironmental Considerations Excessive Noise Waste DisposalWake/Wash Nautical Terms Key to Symbols on Controls & Prints Baja Marine Corp This Page Intentionally Left Blank Docking /Lifting /Trailering Passenger Locations General Boat Arrangement2 Hull Propulsion System Basic Boat Dimensions and Clearances MetricGeneral Deck Layout FIG General Deck LayoutGear Shift and Throttle Control Power Trim Unit and GaugeDescription of Major Controls Trim Tabs Trailer SwitchTachometer and Hour Meter Ignition Shutdown SwitchEngine Alarm System Important GaugesNavigation and Anchor Lights Oil Pressure, Water Temperature, Voltmeter and Fuel GaugesPre-Launch, Launch and Post- Launch Checklist Using Your BoatFueling the Boat Trailer Launching and LoadingPersonal Flotation Devices BoardingStarting the Engine Passenger Instruction and LocationStopping the Engine Shifting to Drive the BoatHydraulic Steering Steering SystemsPower Steering System Power SteeringThis page intentionally left blank Drain Plug Bilge & Underwater GearBilge Fuel & Oil SpillageVibration and Causes Maintenance and ServiceEngines and Stern Drive Bilge BlowersImpact to Stern Drive Propeller Removal and InstallationGear case Anti-Siphon Valve Inboard/Outboard Engine Only Fuel SystemFuel System Static Electricity and the Fuel System Fueling PrecautionsBefore and During Fueling Checklist After Fueling Checklist This page intentionally left blank Batteries Electrical SystemsElectrical Systems Direct Current DCFuse Panel Electrolytic Corrosion & Zinc AnodesBreakers and/or Fuses Marine Electronic Cathodic Anti-corrosion System Mercathode Ignition Switch Drive Pump Switch Panel Wire Information FIG Switch Panel Wire Information FIG Wire Schematic FIG Gauge Panel Electrical Information FIG Options & Accessories Locations Options & AccessoriesCanvas Automatic Fire Extinguisher System OptionFire Extinguisher Port Horn Canvas Care and MaintenanceSwim Platform w/ Ladder Optional Depth Finder OptionalRequirements for Operators Stereo SystemHead Systems Portable Self-Contained HeadPortable Head with Pump-Out Exhaust SystemsThis page intentionally left blank Interval Required Inspection, Service MaintenanceSummary Guide for Inspection, Service and Maintenance Interval Summary Guide For Inspection, Service and MaintenanceUseful Service Information Bilge Area Inspection, Service and Maintenance ProtocolBoat Storage Winterization Checklist for Boats Stored on LandBatteryies Topside and SuppliesMiscellaneous Fitting Out After StorageFuel Systems Fuel SystemSecurity Considerations Power Steering System MaintenanceBoat Systems Quick Reference ChecklistBoarding the Boat General Starting the Engine Returning to Port General Quick Reference Checklist cont’d Departing GeneralIf the Engine Does Not Start Quick Reference Checklist cont’dSecuring the Boat After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Fiberglass & Gelcoat Paint Cleaning Agents & Other SubstancesCare & Refinishing Stains & ScratchesCanvas and Clear Vinyl Permanently Moored or Docked BoatsTopside Areas Acrylic Plastic Sheeting Plastic GlassInterior Upholstery Fabric Exterior Upholstery FabricThis Page Intentionally Left Blank Index Index Performance