Graco SDM15, SDM5, SDP5, SDP15 Error Codes, Error Code Cause Solution, Manual Mode only, Err7

Page 28

Troubleshooting

Error Codes

Error codes are listed below. Even in an error condition the unit keeps track of the amount dispensed. With any error code displayed you can:

•Select Manual option on Home Screen.

Error code is cleared. Unit switches to Manual mode and dispensed amount is displayed.

•Select reset option.

Error code is cleared, Unit switches to Auto mode and the present amount is displayed.

Error Code

Cause

Solution

 

 

 

Err 1

Battery voltage is low

Change battery, page 29.

 

Switch Error: Error occurred with

Ensure that your flow rate is not

 

higher than 14 gpm (37.8 lpm). For

 

pick-up in internal gear.

 

further assistance, contact your

 

or

Err 2

Graco distributor.

 

 

Unit was dropped or unit encoun-

Select Reset, item G, page 21.

 

tered excessive vibration during ship-

 

 

ping.

 

 

 

 

 

Flow has continued after it should

Check for low battery symbol and

 

have shut off.

replace batteries if indicated, page

Err 4

or

29. For further assistance, contact

your Graco distributor.

 

Flow has occurred in lockout condi-

Navigate to Home screen. Then

 

tion.

re-enter Dispense Screen.

 

 

 

 

In Manual Mode only.

Select Reset, item G, page 21 and

Err 5

The unit has dispensed the shut-off

dispense again.To change the

default amount and has stopped fluid

shut-off default amount, see

 

 

flow.

Units/Limits Screen, page 15.

 

 

 

 

A present dispense amount of zero

Enter an amount that is not zero. See

Err 6

was entered for the dispense or is

Preset Dispense Screen, page 22.

stored as the default and a Preset

 

 

 

 

dispense was attempted.

 

 

 

 

 

Battery voltage is too low.

Change battery, page 29.

 

or

 

Err7

CAP ERROR: Error has occurred in

Replace the electronic bezel assem-

control.

bly. (See Manual Meters Parts page

 

 

 

36 or Preset Meters Parts page 38 to

 

 

identify which kit is required for your

 

 

meter).

28

312865R

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Important Safety Instructions List of ModelsModels SDM5 Manual Dispense Electronic MetersModel Number Extension DescriptionSDM15 Manual Dispense Electronic Meters Extension Description Nozzle Fluid TypeSDP5 Preset Dispense Electronic Meters SDP15 Preset Dispense Electronic Meters Skin Injection Hazard Fire and Explosion Hazard Installation Typical Installations FIGMounting Bracket FIG Drum Mount Bracket FIGPressure Relief Procedure Pre-Installation ProcedureInstallation Procedure GroundingInstalling Meter FIG Installing Tube Extension FIGInstalling Nozzle FIG Meter Overview Navigation and ModesWay Menu Navigation Button FIG Meter DisplaySetup Mode Screens Preset MetersTo display the Home Screen Manual MetersMain Setup Screen FIG Displaying Setup Screen from an Operation Mode ScreenMain Screen Features FIG All MetersManual Meters Preset Meters All meters include C E Preset meters also include F GUnits/Limit Screen FIG For All MetersCalibration Number Calibrate Screen FIGFluids Manual Calibration Procedure Recalibrating the Meter FIGChoosing a Calibration Factor From the Calibration Table To attain the most accurate calibrationPreset Screen FIG For Preset Meters OnlyPreset Meters include D, P and Q To set Preset amounts FIGBanner Screen Features D and R Language Screen Features D, S, and TBanner Screen FIG Language Screen FIGDispensing Fluid and Operation Mode Screens Home Screen FIGAll Meters Manual Meters All Meters include Include a DTo reset counter to zero after a dispense To dispense in Manual ModePreset shown Manual Dispense FIGPreset Dispense FIG See for terms D LQTS To modify the amount selectedTo dispense in Preset Mode 50 QTSSee for terms F, G, M P Totals Screen FIGTo display Totals Screen Problem Cause Solution TroubleshootingDo not trigger meter when nozzle Troubleshooting Error Codes Error Code Cause SolutionManual Mode only ErrService Replacing the BatteryTrip Rod Repair DisassemblySDP5 & SDP15 Meters Only Remove and discard o-ring 5 FIG Cleaning Trip Rod Reassembly Ti11938ab Replace 4 screws A. Torque each to 15-25 inch pounds Ref Part Description SDM5 & SDM15 Manual Meters PartsQty Part Description 18a SDP5 & SDP 15 Preset Meters Parts Part Description Qty34c 34b 24d 24c 31a 24b 24a 24e 24f Nozzle 33 and Extension 20 Kits Nozzle 33 and Extension 20 Kits Thermal Relief Kits Nozzle 33 KitsPart No. Description PSI bar Rating Technical Data Graco Extended Metered Dispense Valve Warranty Graco Information

SDP5, SDM5, SDM15, SDP15 specifications

The Graco SDP15, SDM15, SDM5, and SDP5 are innovative airless paint sprayers popular among both professionals and DIY enthusiasts. They represent a range of features and technologies that optimize painting efficiency, precision, and reliability.

The Graco SDP15 is designed for extensive projects and professional use. It boasts an impressive maximum operating pressure of 3000 PSI, allowing for smooth and even application of a variety of coatings, including heavier materials like paints and stains. One of its standout features is the ProControl system, which enables users to adjust the pressure settings on-the-fly, ensuring optimal performance for different surfaces and materials.

The SDM15 is another powerful option, particularly suited for medium to large jobs. This model features a robust motor and a compact design, making it both durable and portable. It includes an easy-to-use Control Pro technology, which minimizes overspray while delivering an even finish. Additionally, the SDM15 integrates a built-in filter, enhancing the longevity of the pump by preventing debris from clogging the system.

For lighter tasks or smaller projects, the Graco SDM5 and SDP5 models are excellent choices. The SDM5 is valued for its lightweight design and ease of maneuverability. It has a suitable PSI range for home improvement tasks, allowing for an efficient painting experience without the complexity. The convenient compact storage feature makes it ideal for homeowners and occasional users.

On the other hand, the SDP5 is specifically designed for users who prioritize user-friendliness. It includes features like a flexible suction tube, allowing users to paint directly from the can, reducing cleanup. The SDP5 also incorporates Graco’s exclusive SmartControl technology, ensuring consistent power and pressure throughout the spraying process.

All four models share key technologies such as the stainless-steel piston pump, which enhances durability and lifespan and the ability to handle a wide array of coatings without the need for thinning.

In conclusion, whether for professional use with the SDP15 and SDM15 or for home projects with the SDM5 and SDP5, Graco's lineup provides a range of versatile, efficient, and user-friendly options. Their focus on technology and practical features makes them a top choice for all painting needs.
Top Page Image Contents