Graco SDP5, SDM15, SDM5, SDP15 important safety instructions Skin Injection Hazard

Page 6

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point dispense valve at anyone or at any part of the body.

•Do not put your hand over the end of the dispense nozzle.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

•Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer.

•Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu- facturer’s replacement parts only.

•Do not alter or modify equipment.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

BATTERY SAFETY

The battery may leak, explode, cause burns, or cause an explosion if mishandled:

•You must use the battery type specified for use with the equipment.

•Sparking can occur when changing batteries. Only replace the battery in a non-hazardous location, away from flammable fluids or fumes.

•Handle and dispose of battery properly - do not short circuit, charge, force over discharge, disas- semble, crush, penetrate, incinerate, or heat the battery to a temperature exceeding 185° F (85° C).

6

312865R

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Important Safety Instructions List of ModelsModel Number ModelsSDM5 Manual Dispense Electronic Meters Extension DescriptionSDM15 Manual Dispense Electronic Meters Extension Description Nozzle Fluid TypeSDP5 Preset Dispense Electronic Meters SDP15 Preset Dispense Electronic Meters Skin Injection Hazard Fire and Explosion Hazard Mounting Bracket FIG InstallationTypical Installations FIG Drum Mount Bracket FIGInstallation Procedure Pressure Relief ProcedurePre-Installation Procedure GroundingInstalling Meter FIG Installing Tube Extension FIGInstalling Nozzle FIG Way Menu Navigation Button FIG Meter OverviewNavigation and Modes Meter DisplayTo display the Home Screen Setup Mode ScreensPreset Meters Manual MetersMain Screen Features FIG Main Setup Screen FIGDisplaying Setup Screen from an Operation Mode Screen All MetersUnits/Limit Screen FIG Manual Meters Preset MetersAll meters include C E Preset meters also include F G For All MetersCalibrate Screen FIG Calibration NumberFluids Choosing a Calibration Factor From the Calibration Table Manual Calibration ProcedureRecalibrating the Meter FIG To attain the most accurate calibrationPreset Meters include D, P and Q Preset Screen FIGFor Preset Meters Only To set Preset amounts FIGBanner Screen FIG Banner Screen Features D and RLanguage Screen Features D, S, and T Language Screen FIGAll Meters Manual Meters Dispensing Fluid and Operation Mode ScreensHome Screen FIG All Meters include Include a DPreset shown To reset counter to zero after a dispenseTo dispense in Manual Mode Manual Dispense FIGPreset Dispense FIG See for terms D LQTS To modify the amount selectedTo dispense in Preset Mode 50 QTSTotals Screen FIG See for terms F, G, M PTo display Totals Screen Troubleshooting Problem Cause SolutionDo not trigger meter when nozzle Troubleshooting Manual Mode only Error CodesError Code Cause Solution ErrService Replacing the BatteryDisassembly Trip Rod RepairSDP5 & SDP15 Meters Only Remove and discard o-ring 5 FIG Cleaning Trip Rod Reassembly Ti11938ab Replace 4 screws A. Torque each to 15-25 inch pounds SDM5 & SDM15 Manual Meters Parts Ref Part DescriptionQty Part Description 18a SDP5 & SDP 15 Preset Meters Parts Part Description Qty34c 34b 24d 24c 31a 24b 24a 24e 24f Nozzle 33 and Extension 20 Kits Nozzle 33 and Extension 20 Kits Nozzle 33 Kits Thermal Relief KitsPart No. Description PSI bar Rating Technical Data Graco Extended Metered Dispense Valve Warranty Graco Information

SDP5, SDM5, SDM15, SDP15 specifications

The Graco SDP15, SDM15, SDM5, and SDP5 are innovative airless paint sprayers popular among both professionals and DIY enthusiasts. They represent a range of features and technologies that optimize painting efficiency, precision, and reliability.

The Graco SDP15 is designed for extensive projects and professional use. It boasts an impressive maximum operating pressure of 3000 PSI, allowing for smooth and even application of a variety of coatings, including heavier materials like paints and stains. One of its standout features is the ProControl system, which enables users to adjust the pressure settings on-the-fly, ensuring optimal performance for different surfaces and materials.

The SDM15 is another powerful option, particularly suited for medium to large jobs. This model features a robust motor and a compact design, making it both durable and portable. It includes an easy-to-use Control Pro technology, which minimizes overspray while delivering an even finish. Additionally, the SDM15 integrates a built-in filter, enhancing the longevity of the pump by preventing debris from clogging the system.

For lighter tasks or smaller projects, the Graco SDM5 and SDP5 models are excellent choices. The SDM5 is valued for its lightweight design and ease of maneuverability. It has a suitable PSI range for home improvement tasks, allowing for an efficient painting experience without the complexity. The convenient compact storage feature makes it ideal for homeowners and occasional users.

On the other hand, the SDP5 is specifically designed for users who prioritize user-friendliness. It includes features like a flexible suction tube, allowing users to paint directly from the can, reducing cleanup. The SDP5 also incorporates Graco’s exclusive SmartControl technology, ensuring consistent power and pressure throughout the spraying process.

All four models share key technologies such as the stainless-steel piston pump, which enhances durability and lifespan and the ability to handle a wide array of coatings without the need for thinning.

In conclusion, whether for professional use with the SDP15 and SDM15 or for home projects with the SDM5 and SDP5, Graco's lineup provides a range of versatile, efficient, and user-friendly options. Their focus on technology and practical features makes them a top choice for all painting needs.
Top Page Image Contents