Furuno CH-37 manual Filling the soundome with sonar oil

Page 14

2.Fill the soundome with sonar oil 6 cm below the top of the dome. (Use only the specified sonar oil. Use of other sonar oils may affect performance.) Reat- tach the soundome.

 

 

Frequency (kHz)

 

 

 

 

 

 

 

 

 

60

 

81

113

 

162

 

 

 

 

 

 

 

Sonar oil 4L

No

 

Yes

Yes

 

Yes

(000-824-033)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Super sonar oil 4L

Yes

 

No

No

 

No

(000-804-568)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ball wrench

Sonar oil

5 cm

Use packing material to support soundome.

CAUTION

WORKING WITH THE SONAR OIL Precautions

Keep oil away from eyes. Wear protective gloves when working with the oil. The oil can cause inflammation of the eyes.

Do not touch the oil. Wear protective gloves when working with the oil. The oil can cause inflammation of the skin.

Do not ingest the oil. Diarrhea or vomiting can result.

Keep the oil out of reach of children.

Emergency

If the oil enters eyes, flush with clean water about 15 minutes. Consult a physician.

If the oil contacts skin, wash with soap and water.

If the oil is ingested, see a physician immediately.

Disposal of oil and its container

Dispose of oil and its container in accord- ance with local regulations. For further details, contact place of purchase.

Storage

Seal container to keep out foreign material. Store in dark place.

Figure 1-4 Filling the soundome with sonar oil

3.Shorten the main shaft by the length of Lt + 110 mm, where Lt is the length of the retraction tank. When the retraction tank length is 1 meter do not shorten the 1.17 meter main shaft.

Supplied Length: 1.17 m (2.2 m, 3.8 m)

Lt + 110 mm

Take care not to

Chamfer edge to

scratch.

protect O-ring from

 

damage.

Figure 1-5 How to shorten the main shaft

1-4

Image 14
Contents Color Sector Scanning Sonar 00080821301 Safety Instructions Working with the Sonar OIL Precautions Table of Contents Equipment Lists Standard SupplyOptional Equipment Name Type Code No RemarksSystem Configuration Hull unit assembly combination Standard OptionThis page is intentionally left blank General mounting considerations Installation position considerations Hull Unit Mounting of transducer tank Mounting methodTank length Assembling and mounting of hull unit Necessary toolsFilling the soundome with sonar oil How to fasten main shaft to soundome assembly Passing main shaft through the main body flange 11 Fastening the hull unit to the transducer tank 12 Installing the raise/lower drive block Checking manual raise/lower of transducer with hand crank 13 Tightening the grease cotton retainerHull unit installation materials Super Sonar OIL 4L Name Outline Descriptions ’TY Remarks Reinforcement Transceiver Unit Mounting considerationsDisplay Unit Grounding the Display Unit and Transceiver UnitExternal Interface Option Mounting procedureMotion Sensor MS-100 Option 19 Display unit, rear view Logarithm Amplifier Video Sounder Bind cables with the cable tie suppliedPage 21 Installation Position of Clinometer Clinometer BS-704 OptionPage Wiring Wiring Among UnitsCabling diagram Page Synchronizing Transmission with Echo Sounder or Other Sonar Connections for synchronizing Tx with other E/S, sonarMenu setting Press the Menu key Select Sonar at the top of the menuThis page is intentionally left blank Adjustments General ChecksSelecting audio frequency Adjustment of Transceiver UnitSignal offset adjustment Heading Alignment Horizontal beamwidthAdjustment of Motion Sensor, Clinometer Main shaftSoundome Painting Measuring ship’s semi-permanent inclination angleLED Status Display unitLEDs in the display unit con’t Transceiver unit Transceiver unit LEDs in the transceiver unitLEDs in the transceiver unit con’t Hull unit LEDs in the hull unitChanging Specifications System MenuSystem setting menu description Page Page Page Page 000-803-168-00 Jan Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page カラーセクタースキャニングソナー