Furuno CH-37 manual Motion Sensor MS-100 Option, External Interface Option, Mounting procedure

Page 25

1.5Motion Sensor MS-100 (Option)

The MS-100 measures ship’s pitching and rolling angles with sensors using the principles of the gyroscope. The MS-100 is free from error caused by ship’s ver- tical and horizontal motion. Therefore, it can be installed at any convenient loca- tion. However, ship’s semi-permanent inclination due to loading imbalance cannot be detected. Compensate for this as described in Chapter 3.

Mounting considerations

• Vibration in the mounting area should be FORE

minimal.	θ ≤ 5°
minimal.
• Locate the unit away from areas subject
to water splash.
• The ambient temperature should not ex-	AFT
• The ambient temperature should not ex-
ceed 50°C.

Figure 1-18 Motion sensor MS-100

Mounting procedure

Orient the FORE mark on the unit toward the ship’s bow and mount the unit level to within 5° in all directions.

1.6External Interface (Option)

This section shows how to install External E/S Interface (type OP06-13) and/or the External Monitor Interface (type OP06-14).

For connecting external monitor, prepare mini D-SUB 15 pin cable (male-male).

Recommended cable : EVNPSO5-50ft, manufactured by Black Box Japan Co.,Ltd.

External monitor interface installation kit

Part	Type, Q'ty	Code No.	Q'ty

External Monitor Interface Assy.	-	-	1

XH Connector Assy.	06-313 (13-13P)	006-550-840	1

Screw	M3x6	000-881-103	4

Screw	M3x8	000-881-404	1

Cable Ties	No.249	000-515-871	1

1-15

Image 25

Contents Color Sector Scanning Sonar 00080821301 Safety Instructions Working with the Sonar OIL Precautions Table of Contents Standard Supply Equipment ListsName Type Code No Remarks Optional EquipmentSystem Configuration Standard Option Hull unit assembly combinationThis page is intentionally left blank Hull Unit Installation position considerationsGeneral mounting considerations Tank length Mounting methodMounting of transducer tank Necessary tools Assembling and mounting of hull unitFilling the soundome with sonar oil How to fasten main shaft to soundome assembly Passing main shaft through the main body flange 11 Fastening the hull unit to the transducer tank 12 Installing the raise/lower drive block 13 Tightening the grease cotton retainer Checking manual raise/lower of transducer with hand crankHull unit installation materials Super Sonar OIL 4L Name Outline Descriptions ’TY Remarks Reinforcement Mounting considerations Transceiver UnitGrounding the Display Unit and Transceiver Unit Display UnitMotion Sensor MS-100 Option Mounting procedureExternal Interface Option 19 Display unit, rear view Bind cables with the cable tie supplied Logarithm Amplifier Video SounderPage Clinometer BS-704 Option 21 Installation Position of ClinometerPage Wiring Among Units WiringCabling diagram Page Connections for synchronizing Tx with other E/S, sonar Synchronizing Transmission with Echo Sounder or Other SonarPress the Menu key Select Sonar at the top of the menu Menu settingThis page is intentionally left blank General Checks AdjustmentsSignal offset adjustment Adjustment of Transceiver UnitSelecting audio frequency Horizontal beamwidth Heading AlignmentMain shaft Adjustment of Motion Sensor, ClinometerMeasuring ship’s semi-permanent inclination angle Soundome PaintingDisplay unit LED StatusLEDs in the display unit con’t Transceiver unit LEDs in the transceiver unit Transceiver unitLEDs in the transceiver unit con’t LEDs in the hull unit Hull unitSystem Menu Changing SpecificationsSystem setting menu description Page Page Page Page 000-803-168-00 Jan Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page カラーセクタースキャニングソナー