American Dynamics ADCC1100 manual Controlling the Camera Iris, Controlling Camera Flip, Auto Iris

Page 22

ADCC1100

Controlling the Camera Iris

Normally, the brightness of a picture is controlled by the camera's auto iris or other feature. However, there may be times when the operator needs the picture on the monitor to appear lighter or darker. To brighten the picture, press the OPEN iris key. To darken the picture, press the CLOSE iris key.

CLOSE Iris

OPEN Iris

Controlling Camera Flip

To "flip" the camera under keyboard control 180O from its current position (for uninter- rupted surveillance of objects which pass directly beneath the camera), use the flip soft key.

To flip the camera:

1.Press the OPERATOR tab key.

2.Press the NEXT soft key.

3.Press the FLIP soft key.

Note: on suitably equipped dome cameras with the auto-flip function turned on, the dome flips automatically when the subject passes directly beneath the camera.

Auto Iris

Certain cameras are designed with Auto Iris capability. The feature can be enabled from the keyboard as follows.

To enable auto iris:

1.Press the OPERATOR tab key.

2.Press the NEXT soft key.

3.Press the AUTO IRIS soft key.

Note: using the manual OPEN or CLOSE iris key will override the Auto Iris function as long as either of these keys is held down. The camera may or may not then return to auto iris mode after a time interval, or it may stay in manual iris mode. This depends on the camera under control and how the camera has been set up.

16

Image 22
Contents ControlCenterTM Copyright Keyboard Installation and Operation Avertissement Elektromagnetische Kompatibilität Funkfrequenzemissionen Advertencia About the ADCC1100 Keyboard Programming with the ADCC1100 Keyboard Key Features About the ADCC1100 KeyboardADCC1100 Keyboard Overview Page Setting the Jumpers for the MP-KMI Connection and Setup of the ADCC1100Supplied Equipment Installation Connections for Cable Distance of Seven Feet or LessConnections for Cable Distance of Greater than Seven Feet Configuring for MP48, AD1024 or Quicksite Mode Keyboard Access Control Basic OperationsLogging on to the Keyboard Mode Welcome screenPlease Enter PIN Keyboard Menu Navigation Entering DataSelecting Monitors Calling a Camera to View on a MonitorControlling a Camera’s Pan, Tilt and Zoom Controlling Camera FocusControlling Camera Flip Controlling the Camera IrisAuto Iris Calling Presets Shots Running System ToursCalling a Scratch Pad Tour Acknowledging Alarms Calling SalvosAuxiliaries Setting the Keyboard Display BrightnessSetting the Keyboard Display Contrast Enabling or Disabling the Keyboard Audible WarningViewing Satellite Sites-Quicksite Mode Viewing Satellite SitesRunning Patterns Selecting and Running a MacroSelecting the Macro Running a MacroOperating a VCR or Digital Recorder VCR Control MenuProgramming with the ADCC1100 Keyboard Setting PresetsProgramming Dome Patterns Setting Scratch Pad Tours Dome Menu FunctionsNavigating Dome Camera Menus Dome Menu NavigationProgramming Macros Locking and Unlocking a CameraStage 1 Programming the Macro Page and Macro Icon Configure Macro Menu Programming a Macro Page NameStoring the Macro Page Configuration to the Smart Card Programming a Macro IconStage 2 Programming a Macro Example 1 Quick Switch function Advanced MacrosProgramming Smart Cards Reading a Smart CardProgramming a Smart Card Programming a New Smart CardConfiguring Partitions Copying Macro Information from One Smart Card to AnotherPartition Menu Page Matrix Menu Matrix MenuSetting the Baud Rate Installer FunctionsEnabling Lens Macro Keys Configuring for MP48, AD1024 or Quicksite Mode Quicksite ConfigurationConfiguring Satellite Sites Start EndReading Quicksite Settings on a Smart Card Copying Quicksite Settings from One Smart Card to AnotherAppendix a Monitor Arming Commands Monitor Arming Code Monitor Acronym Command SequenceAppendix B Macro Reference Sheet Keyboard Installation and Operation Appendix C Macro Icon Reference Numbers Keyboard Installation and Operation 100 Appendix D Troubleshooting Problem Check ListAppendix E Specifications Model NumbersIndex Keyboard Installation and Operation Running Multiple Macros Keyboard Installation and Operation Please visit our website for more information