Roland VC-1 D-50 owner manual Transferring Patches from the VC-1 to the D-50/550, Touch System

Page 33

Transferring Patches To and From the D-50/550

Transferring Patches from the VC-1 to the D-50/550

Using the D-50

3-1

3-2

4-1, 4-2

12

4-3

1.Use a MIDI cable to connect the V-Synth XT’s MIDI OUT connector to the D-50’s MIDI IN connector.

2.Set the D-50 and V-Synth XT to the same MIDI channel (the basic channel; p. 73).

3.Turn the Memory Protect of the D-50 to OFF.

3-1.Press the [TUNE/FUNCTION] button.

3-2.Select “Protect” with the Selector button and turn it OFF with the joystick.

4.Enable reception of bulk load data on the D-50.

4-1.Press the D-50’s [DATA TRANSFER] button.

4-2.While pressing the D-50’s [DATA TRANSFER] button, specify (B.Load) with the Selector button.

4-3.Press the D-50’s ENTER] button.

5.Turn the Exclusive Sw of the V-Synth XT to On.

5-1.Press [MODE].

5-2.Touch <SYSTEM>.

5-3.Select “Exclusive Sw,” then turn the V-Synth XT’s VALUE dial to specify On.

6.Press [MODE] on the V-Synth XT. The MODE MENU window appears.

7. Touch <DATA TRANSFER>. The DATA TRANSFER screen appears.

8.Touch <B.Dump> in the left of the screen. The MIDI Bulk Dump screen appears.

9.Modify the value by either turning the VALUE dial or pressing

[INC/+] or [DEC/-].

Source Bank

Selects the Patch Bank in the VC-1 with the patch data to transfer to the D-50.

Value: I1 – I8, P1 – P6

10.Touch <OK>. The bulk dump starts. If you want to cancel without executing, touch <Cancel>.

11.When the data transfer is completed, the D-50’s display shows “Complete.”

12.Press the [EXIT] button on the D-50 to return to the play mode.

33

Image 33

Contents 03897845 ’05-3-1N Page Page Table of Contents Table of Contents Introduction Main FeaturesPerfect Simulation of the D-50’s Tones Editing and Performances That Surpass the OriginalWhat is the digital synthesizer D-50? Panel Descriptions Front PanelNumber KEY Mode ShiftExit Rear Panel Try Out the Sounds Turning On the PowerSelecting Patches and Playing Sounds Selecting Patches with the Value dial Selecting Patches from the ListSelecting Patches with Patch Palette Enabling or Disabling the Beep Tone Viewing Various Information01ePatchFactorImage Applying Effects to the SoundAssigning Parameters to the Controllers Controllers ParametersKeys Functions List OSC1, OSC2, COSM1, COSM2 and TVA Specify the Tones or the Partials to be appliedYou can control the following parameters Settings Common to All Screens How to Make the Patch FactorsDual WholeSplit SEPMode Portamento Mode Hold Hold ModeBend Bender Range Value AfterPB Aftertouch, Pitch BenderOutput Output Mode Mode Output ModeValue Display Function RevType Reverb Type Vol Total VolumeValue Display Description Revbal Reverb BalanceULL ULU Mode Chase ModeLevel Chase Level Value Time Chase TimeUTune Fine Tuning of the Upper Tone LTune Fine Tuning of the Lower ToneTxBS Transmit Bank Select Switch SepCH Receive Channel in Separate ModeNaming a Patch Saving Patches You’ve CreatedSaving Patches Reset to Default Factory Settings Touch Factory RESET. The Factory Reset screen appearsVC-1’s File Structure Transferring Patches from the D-50 to the VC-1 Transferring Patches To and From the D-50/550Using the D-50 Using the D-550Transfer the patch from the memory card to the D-50/550 Transferring Patches from the D-50/550 to the VC-1 Touch Data TRANSFER. The Data Transfer screen appears Saving Transferred PatchesDEC Source Bank Destination BankTransferring Patches from the VC-1 to the D-50/550 Touch SystemINC/+ or DEC Source Bank 3-1 Copying a Reverb Type Value 17 Value1 Destination BankMemory Structure Overview of the VC-1Work Area Temporary AreaBasic Concept of a Tone PartialSynthesizer sound generator PCM sound generator StructureTone Patch Ring ModulatorWG Wave Generator Structure of Tone ParametersTVA Time Variant Amplifier TVF Time Variant FilterENV Envelope Generator LFO Low FrequencyCreating a Patch How to Make the Patch SettingsEditing a Value Useful Functions for EditingUndoing an editing Operation Cursor ButtonsSilencing the Sound of the Partial Editing with the Panel Controls Partial SelectCopying Tone Settings CancelDisplay Value ALL Copying Parameter SettingsCommon TVFAuditioning the Sound Before Editing When Is set to All or Common Setting is ignoredCtrl Setup Initializing Patch SettingsCheck All Patch FactorCommon Parameters Tone ParametersStructure EQ/CHORUSENV Edit Envelope ENV Pitch EnvelopeENV Time Edit Velo Velocity RangeENV Level Edit Pitch Mod Pitch Modulation LFO Low Frequency OscillatorEQ Edit Equalizer EQ/CHORUS Equalizer/ChorusOFF KEYChorus Edit Pitch Partial ParametersWG Form Waveform WG Form WG WaveformWG PW WG Pulse Width Wave WaveformDisplay LFO Phase Value -7-+7 After Aftertouch RangeValue -7-+7 LFO LFO Select Coars Pitch Coarse WG PitchValue C1-C7 Fine Pitch Fine KF Keyfollow pitchENV P-ENV Mode LFO LFO ModeBend Bender Mode WG Mod WG ModulationBender Mode Example TVF Time Variant FilterFreq Cutoff Frequency KFKeyfollow Cutoff Point Reso ResonanceBP Bias Point Display Example Example FunctionTVF ENV TVF Envelope Value T5 Time TVF ENV TimeTVF ENV Level TVA Time Variant Amplifier Value Volume AdjustmentValue -50-+50 BP Bias Point Display Example Function ExampleTVA ENV Envelope TVA ENV TimeVelo Velocity Follow Time TVA ENV Level Value -7-+7 MOD ModulationTVA MOD Settings for the Entire VC-1 How to Make the System Function SettingsDEC Master Tune Sound SettingSound Character Digital Freq Digital FrequencyProg.C Program Change Switch SeparateCH Receive Channel in Separate ModeMidi CH Midi Channel Value 1Bank.S Bank Select Switch Exclusive Exclusive SwitchDump TxEDITInitializing the System Settings Mono Mode, Poly Mode Key Mode AlterationDual Key Mode Poly Mode Mono Mode Mode Message OffDual-S SplitP1 Preset 1Original D-50 Preset PatchesP2 Preset 2 New Sound ListP4 Preset 4PN-D50-02 P3 Preset 3PN-D50-01P5 Preset 5PN-D50-03 P6 Preset 6PN-D50-04BANK1 Patch Factors Value Comment Patch FactorsTone Parameters Common ParametersParameter Value Parameter Value Comment Partial ParametersTVF ENV Midich System ParametersOneshot WaveformLoop Number Display PCM NameLoop Some of the sounds 1 to 76, are combined and looped Newly Added WaveformsNumber Display Data Transmission Midi ImplementationReceive data Mono Controller number Exclusive Communication Partial Parameter Common Parameter Patch Parameter Supplementary Material Midi Implementation Chart VC-1 V-Card D-50 SpecificationsIndex Index 100