Roland VC-1 D-50 owner manual TVA ENV Level, T4 Time

Page 68

Tone Parameters

T4 (Time 4

Sets the time needed to reach point 4 from point 3.

Value: 0–100

T5 (Time 5)

Sets the time needed to reach point 5 from the moment the key is released.

Value: 0–100

TVA ENV Level

L1 (Level 1)

Sets the level of point 1.

Value: 0–100

L2 (Level 2)

Sets the level of point 2.

Value: 0–100

L3 (Level 3)

Sets the level of point 3.

Value: 0–100

SusL (Sustain Level)

Sets the level of point 4.

Value: 0–100

EndL (End Level)

To lower the level after releasing the key, set this to 0, and to raise the level, set it to 100. Value: 0, 100

*The End Level remains until the key is released and played again. That is, at a value of 100, the sound remains. However, the PMC Sound Generator’s One-shot sounds do not remain even when set to 100.

*If the levels of two adjacent points are set to similar values, the time between these two points may prove to be shorter than what is actually set, or even zero.

68

Image 68

Contents 03897845 ’05-3-1N Page Page Table of Contents Table of Contents Main Features IntroductionPerfect Simulation of the D-50’s Tones Editing and Performances That Surpass the OriginalWhat is the digital synthesizer D-50? Number KEY Panel DescriptionsFront Panel Exit ModeShift Rear Panel Turning On the Power Try Out the SoundsSelecting Patches and Playing Sounds Selecting Patches with Patch Palette Selecting Patches with the Value dialSelecting Patches from the List Viewing Various Information Enabling or Disabling the Beep ToneApplying Effects to the Sound 01ePatchFactorImageKeys Functions Assigning Parameters to the ControllersControllers Parameters Specify the Tones or the Partials to be applied List OSC1, OSC2, COSM1, COSM2 and TVAYou can control the following parameters How to Make the Patch Factors Settings Common to All ScreensWhole DualSplit SEPHold Hold Mode Mode Portamento ModeBend Bender Range Value AfterPB Aftertouch, Pitch BenderValue Display Function Output Output ModeMode Output Mode Vol Total Volume RevType Reverb TypeValue Display Description Revbal Reverb BalanceMode Chase Mode ULL ULULevel Chase Level Value Time Chase TimeLTune Fine Tuning of the Lower Tone UTune Fine Tuning of the Upper ToneTxBS Transmit Bank Select Switch SepCH Receive Channel in Separate ModeSaving Patches You’ve Created Naming a PatchSaving Patches VC-1’s File Structure Reset to Default Factory SettingsTouch Factory RESET. The Factory Reset screen appears Transferring Patches To and From the D-50/550 Transferring Patches from the D-50 to the VC-1Transfer the patch from the memory card to the D-50/550 Using the D-50Using the D-550 Transferring Patches from the D-50/550 to the VC-1 Saving Transferred Patches Touch Data TRANSFER. The Data Transfer screen appearsDEC Source Bank Destination BankINC/+ or DEC Source Bank Transferring Patches from the VC-1 to the D-50/550Touch System 3-1 Copying a Reverb Type Value1 Destination Bank Value 17Overview of the VC-1 Memory StructureWork Area Temporary AreaSynthesizer sound generator Basic Concept of a TonePartial Tone PCM sound generatorStructure Ring Modulator PatchStructure of Tone Parameters WG Wave GeneratorTVF Time Variant Filter TVA Time Variant AmplifierENV Envelope Generator LFO Low FrequencyHow to Make the Patch Settings Creating a PatchUseful Functions for Editing Editing a ValueUndoing an editing Operation Cursor ButtonsEditing with the Panel Controls Partial Select Silencing the Sound of the PartialDisplay Value Copying Tone SettingsCancel Copying Parameter Settings ALLCommon TVFWhen Is set to All or Common Setting is ignored Auditioning the Sound Before EditingInitializing Patch Settings Ctrl SetupCheck All Patch FactorTone Parameters Common ParametersStructure EQ/CHORUSENV Pitch Envelope ENV Edit EnvelopeENV Time Edit Velo Velocity RangeENV Level Edit LFO Low Frequency Oscillator Pitch Mod Pitch ModulationEQ/CHORUS Equalizer/Chorus EQ Edit EqualizerOFF KEYChorus Edit Partial Parameters PitchWG Form WG Waveform WG Form WaveformWG PW WG Pulse Width Wave WaveformValue -7-+7 LFO LFO Select Display LFO PhaseValue -7-+7 After Aftertouch Range WG Pitch Coars Pitch CoarseValue C1-C7 Fine Pitch Fine KF Keyfollow pitchLFO LFO Mode ENV P-ENV ModeBend Bender Mode WG Mod WG ModulationFreq Cutoff Frequency Bender Mode ExampleTVF Time Variant Filter Reso Resonance KFKeyfollow Cutoff PointBP Bias Point Display Example Example FunctionTVF ENV TVF Envelope TVF ENV Time Value T5 TimeTVF ENV Level Value Volume Adjustment TVA Time Variant AmplifierValue -50-+50 BP Bias Point Display Example Function ExampleVelo Velocity Follow Time TVA ENV EnvelopeTVA ENV Time TVA ENV Level MOD Modulation Value -7-+7TVA MOD DEC Settings for the Entire VC-1How to Make the System Function Settings Sound Setting Master TuneSound Character Digital Freq Digital FrequencySeparateCH Receive Channel in Separate Mode Prog.C Program Change SwitchMidi CH Midi Channel Value 1Exclusive Exclusive Switch Bank.S Bank Select SwitchDump TxEDITInitializing the System Settings Key Mode Alteration Mono Mode, Poly ModeKey Mode Poly Mode Mono Mode Mode Message Off DualDual-S SplitPreset Patches P1 Preset 1Original D-50P2 Preset 2 New Sound ListP3 Preset 3PN-D50-01 P4 Preset 4PN-D50-02BANK1 P5 Preset 5PN-D50-03P6 Preset 6PN-D50-04 Patch Factors Patch Factors Value CommentParameter Value Tone ParametersCommon Parameters Partial Parameters Parameter Value CommentTVF ENV System Parameters MidichWaveform OneshotLoop Number Display PCM NameNumber Display Loop Some of the sounds 1 to 76, are combined and loopedNewly Added Waveforms Midi Implementation Data TransmissionReceive data Mono Controller number Exclusive Communication Partial Parameter Common Parameter Patch Parameter Supplementary Material Midi Implementation Chart Specifications VC-1 V-Card D-50Index Index 100