Roland VC-1 D-50 owner manual Editing with the Panel Controls Partial Select

Page 45

Creating a Patch

Editing with the Panel Controls (Partial Select)

You can assign a variety of parameters (such as TVF Resonance or TVA Level) to the knobs at the right of the front panel for direct, intuitive editing of the parameters.

The partials to which the tone parameters assigned to the different knobs are applied are specified in the PATCH TOP screen or with STRUCTURE [1] at the right of the front panel. You can use the knobs to edit the tone parameters of the partial whose indicator is lit.

Off Off On Off

*The Partial select setting will be written into the VC-1 by taking the saving procedure. (p. 27)

Silencing the Sound of the Partial

While editing a Partial parameter, any Partial sound can be muted (Partial Mute).

Partials to be muted are specified in the PATCH TOP screen or with STRUCTURE [3] at the right of the front panel. The partial is muted when the indicator is off; muting is defeated when the indicator is lit.

Off Off Off On

*The Partial Mute setting will be written into the VC-1 by taking the saving procedure. (p. 27)

45

Image 45

Contents 03897845 ’05-3-1N Page Page Table of Contents Table of Contents Introduction Main FeaturesPerfect Simulation of the D-50’s Tones Editing and Performances That Surpass the OriginalWhat is the digital synthesizer D-50? Panel Descriptions Front PanelNumber KEY Mode ShiftExit Rear Panel Try Out the Sounds Turning On the PowerSelecting Patches and Playing Sounds Selecting Patches with the Value dial Selecting Patches from the ListSelecting Patches with Patch Palette Enabling or Disabling the Beep Tone Viewing Various Information01ePatchFactorImage Applying Effects to the SoundAssigning Parameters to the Controllers Controllers ParametersKeys Functions List OSC1, OSC2, COSM1, COSM2 and TVA Specify the Tones or the Partials to be appliedYou can control the following parameters Settings Common to All Screens How to Make the Patch FactorsDual WholeSplit SEPMode Portamento Mode Hold Hold ModeBend Bender Range Value AfterPB Aftertouch, Pitch BenderOutput Output Mode Mode Output ModeValue Display Function RevType Reverb Type Vol Total VolumeValue Display Description Revbal Reverb BalanceULL ULU Mode Chase ModeLevel Chase Level Value Time Chase TimeUTune Fine Tuning of the Upper Tone LTune Fine Tuning of the Lower ToneTxBS Transmit Bank Select Switch SepCH Receive Channel in Separate ModeNaming a Patch Saving Patches You’ve CreatedSaving Patches Reset to Default Factory Settings Touch Factory RESET. The Factory Reset screen appearsVC-1’s File Structure Transferring Patches from the D-50 to the VC-1 Transferring Patches To and From the D-50/550Using the D-50 Using the D-550Transfer the patch from the memory card to the D-50/550 Transferring Patches from the D-50/550 to the VC-1 Touch Data TRANSFER. The Data Transfer screen appears Saving Transferred PatchesDEC Source Bank Destination BankTransferring Patches from the VC-1 to the D-50/550 Touch SystemINC/+ or DEC Source Bank 3-1 Copying a Reverb Type Value 17 Value1 Destination BankMemory Structure Overview of the VC-1Work Area Temporary AreaBasic Concept of a Tone PartialSynthesizer sound generator PCM sound generator StructureTone Patch Ring ModulatorWG Wave Generator Structure of Tone ParametersTVA Time Variant Amplifier TVF Time Variant FilterENV Envelope Generator LFO Low FrequencyCreating a Patch How to Make the Patch SettingsEditing a Value Useful Functions for EditingUndoing an editing Operation Cursor ButtonsSilencing the Sound of the Partial Editing with the Panel Controls Partial SelectCopying Tone Settings CancelDisplay Value ALL Copying Parameter SettingsCommon TVFAuditioning the Sound Before Editing When Is set to All or Common Setting is ignoredCtrl Setup Initializing Patch SettingsCheck All Patch FactorCommon Parameters Tone ParametersStructure EQ/CHORUSENV Edit Envelope ENV Pitch EnvelopeENV Time Edit Velo Velocity RangeENV Level Edit Pitch Mod Pitch Modulation LFO Low Frequency OscillatorEQ Edit Equalizer EQ/CHORUS Equalizer/ChorusOFF KEYChorus Edit Pitch Partial ParametersWG Form Waveform WG Form WG WaveformWG PW WG Pulse Width Wave WaveformDisplay LFO Phase Value -7-+7 After Aftertouch RangeValue -7-+7 LFO LFO Select Coars Pitch Coarse WG PitchValue C1-C7 Fine Pitch Fine KF Keyfollow pitchENV P-ENV Mode LFO LFO ModeBend Bender Mode WG Mod WG ModulationBender Mode Example TVF Time Variant FilterFreq Cutoff Frequency KFKeyfollow Cutoff Point Reso ResonanceBP Bias Point Display Example Example FunctionTVF ENV TVF Envelope Value T5 Time TVF ENV TimeTVF ENV Level TVA Time Variant Amplifier Value Volume AdjustmentValue -50-+50 BP Bias Point Display Example Function ExampleTVA ENV Envelope TVA ENV TimeVelo Velocity Follow Time TVA ENV Level Value -7-+7 MOD ModulationTVA MOD Settings for the Entire VC-1 How to Make the System Function SettingsDEC Master Tune Sound SettingSound Character Digital Freq Digital FrequencyProg.C Program Change Switch SeparateCH Receive Channel in Separate ModeMidi CH Midi Channel Value 1Bank.S Bank Select Switch Exclusive Exclusive SwitchDump TxEDITInitializing the System Settings Mono Mode, Poly Mode Key Mode AlterationDual Key Mode Poly Mode Mono Mode Mode Message OffDual-S SplitP1 Preset 1Original D-50 Preset PatchesP2 Preset 2 New Sound ListP4 Preset 4PN-D50-02 P3 Preset 3PN-D50-01P5 Preset 5PN-D50-03 P6 Preset 6PN-D50-04BANK1 Patch Factors Value Comment Patch FactorsTone Parameters Common ParametersParameter Value Parameter Value Comment Partial ParametersTVF ENV Midich System ParametersOneshot WaveformLoop Number Display PCM NameLoop Some of the sounds 1 to 76, are combined and looped Newly Added WaveformsNumber Display Data Transmission Midi ImplementationReceive data Mono Controller number Exclusive Communication Partial Parameter Common Parameter Patch Parameter Supplementary Material Midi Implementation Chart VC-1 V-Card D-50 SpecificationsIndex Index 100