Roland VC-1 D-50 Settings for the Entire VC-1, How to Make the System Function Settings, Dec

Page 71

Settings for the Entire VC-1

Settings that affect the entire operating environment of the VC-1, such as tuning and MIDI message reception, are referred to as System functions. This section explains how to make settings for the System functions and describes the functions of the different System parameters.

How to Make the System Function Settings

fig.10-01(LCD_ModeMenu)

1.Press [MODE]. The MODE MENU window appears.

2.Touch <SYSTEM>. The SYSTEM screen appears.

fig.10-02(LCD_SystemGeneral)

3.Move the cursor to the value box of that parameter. Then modify the value by either turning the VALUE dial or pressing [INC/+] or

[DEC/-].

4.Repeat steps 3 to make the settings for the System function.

5.After you have edited the settings of the System function, touch <Write>, located in the lower right of the screen.

*Changes you make to the System function settings are only temporary—they will be discarded as soon as the power is turned off. If you want to keep any changes you’ve made in the system settings, you must save them in VC-1. When you perform the save procedure, the data that previously occupied the save destination will be lost. However, the factory setting data can be recovered by performing the Initialization procedure. (Factory Reset; p. 28)

71

Image 71

Contents 03897845 ’05-3-1N Page Page Table of Contents Table of Contents Editing and Performances That Surpass the Original Main FeaturesIntroduction Perfect Simulation of the D-50’s TonesWhat is the digital synthesizer D-50? Number KEY Panel DescriptionsFront Panel Exit ModeShift Rear Panel Try Out the Sounds Turning On the PowerSelecting Patches and Playing Sounds Selecting Patches with Patch Palette Selecting Patches with the Value dialSelecting Patches from the List Enabling or Disabling the Beep Tone Viewing Various Information01ePatchFactorImage Applying Effects to the SoundKeys Functions Assigning Parameters to the ControllersControllers Parameters List OSC1, OSC2, COSM1, COSM2 and TVA Specify the Tones or the Partials to be appliedYou can control the following parameters Settings Common to All Screens How to Make the Patch FactorsSEP WholeDual SplitValue AfterPB Aftertouch, Pitch Bender Hold Hold ModeMode Portamento Mode Bend Bender RangeValue Display Function Output Output ModeMode Output Mode Revbal Reverb Balance Vol Total VolumeRevType Reverb Type Value Display DescriptionValue Time Chase Time Mode Chase ModeULL ULU Level Chase LevelSepCH Receive Channel in Separate Mode LTune Fine Tuning of the Lower ToneUTune Fine Tuning of the Upper Tone TxBS Transmit Bank Select SwitchNaming a Patch Saving Patches You’ve CreatedSaving Patches VC-1’s File Structure Reset to Default Factory SettingsTouch Factory RESET. The Factory Reset screen appears Transferring Patches from the D-50 to the VC-1 Transferring Patches To and From the D-50/550Transfer the patch from the memory card to the D-50/550 Using the D-50Using the D-550 Transferring Patches from the D-50/550 to the VC-1 Destination Bank Saving Transferred PatchesTouch Data TRANSFER. The Data Transfer screen appears DEC Source BankINC/+ or DEC Source Bank Transferring Patches from the VC-1 to the D-50/550Touch System 3-1 Copying a Reverb Type Value 17 Value1 Destination BankTemporary Area Overview of the VC-1Memory Structure Work AreaSynthesizer sound generator Basic Concept of a TonePartial Tone PCM sound generatorStructure Patch Ring ModulatorWG Wave Generator Structure of Tone ParametersLFO Low Frequency TVF Time Variant FilterTVA Time Variant Amplifier ENV Envelope GeneratorCreating a Patch How to Make the Patch SettingsCursor Buttons Useful Functions for EditingEditing a Value Undoing an editing OperationSilencing the Sound of the Partial Editing with the Panel Controls Partial SelectDisplay Value Copying Tone SettingsCancel TVF Copying Parameter SettingsALL CommonAuditioning the Sound Before Editing When Is set to All or Common Setting is ignoredPatch Factor Initializing Patch SettingsCtrl Setup Check AllEQ/CHORUS Tone ParametersCommon Parameters StructureVelo Velocity Range ENV Pitch EnvelopeENV Edit Envelope ENV Time EditENV Level Edit Pitch Mod Pitch Modulation LFO Low Frequency OscillatorKEY EQ/CHORUS Equalizer/ChorusEQ Edit Equalizer OFFChorus Edit Pitch Partial ParametersWave Waveform WG Form WG WaveformWG Form Waveform WG PW WG Pulse WidthValue -7-+7 LFO LFO Select Display LFO PhaseValue -7-+7 After Aftertouch Range KF Keyfollow pitch WG PitchCoars Pitch Coarse Value C1-C7 Fine Pitch FineWG Mod WG Modulation LFO LFO ModeENV P-ENV Mode Bend Bender ModeFreq Cutoff Frequency Bender Mode ExampleTVF Time Variant Filter Display Example Example Function Reso ResonanceKFKeyfollow Cutoff Point BP Bias PointTVF ENV TVF Envelope Value T5 Time TVF ENV TimeTVF ENV Level Display Example Function Example Value Volume AdjustmentTVA Time Variant Amplifier Value -50-+50 BP Bias PointVelo Velocity Follow Time TVA ENV EnvelopeTVA ENV Time TVA ENV Level Value -7-+7 MOD ModulationTVA MOD DEC Settings for the Entire VC-1How to Make the System Function Settings Digital Freq Digital Frequency Sound SettingMaster Tune Sound CharacterValue 1 SeparateCH Receive Channel in Separate ModeProg.C Program Change Switch Midi CH Midi ChannelTxEDIT Exclusive Exclusive SwitchBank.S Bank Select Switch DumpInitializing the System Settings Mono Mode, Poly Mode Key Mode AlterationSplit Key Mode Poly Mode Mono Mode Mode Message OffDual Dual-SSound List Preset PatchesP1 Preset 1Original D-50 P2 Preset 2 NewP4 Preset 4PN-D50-02 P3 Preset 3PN-D50-01BANK1 P5 Preset 5PN-D50-03P6 Preset 6PN-D50-04 Patch Factors Value Comment Patch FactorsParameter Value Tone ParametersCommon Parameters Parameter Value Comment Partial ParametersTVF ENV Midich System ParametersNumber Display PCM Name WaveformOneshot LoopNumber Display Loop Some of the sounds 1 to 76, are combined and loopedNewly Added Waveforms Data Transmission Midi ImplementationReceive data Mono Controller number Exclusive Communication Partial Parameter Common Parameter Patch Parameter Supplementary Material Midi Implementation Chart VC-1 V-Card D-50 SpecificationsIndex Index 100