Roland Complete Guide to Troubleshooting Error Messages in JV-1010 Recording Equipment
Page 53

Error Messages

An error message appears in the display when an error in operation occurs, or if an operation cannot be processed correctly. When this occurs, continue by following the instructions indicated in the error message.

coE (MIDI Communication Error)

noP (No Patch)

fig.coE

fig.noP

 

 

 

 

 

 

 

 

Situation: There is a problem with the MIDI cable connected to the JV-1010’s MIDI IN connector or with an external device. However, this message is also displayed when the power for the external device is turned off.

Action: Check to make sure the MIDI cable is firmly and properly connected. Otherwise confirm that there is no short in the MIDI cable (try switching the MIDI cable to check this).

bFL (MIDI Buffer Full)

fig.bFL

Situation: More MIDI messages were received in a short time than could be processed correctly.

Action: Reduce the amount of MIDI messages that are transmitted.

cSE (MIDI Check Sum Error)

fig.cSE

Situation: A system exclusive message that was received

had an incorrect check sum value.

Action: Correct the check sum value.

rdE (Receive Data Error)

fig.rdE

Situation: If no expansion board is installed, then an expansion board patch or rhythm set is specified from the external MIDI device.

Action: Reselect the patch and rhythm set.

und (User Memory Damaged)

Appendices

 

fig.und

 

 

Situation:

USER data has been damaged.

 

Action:

Restore the factory settings with the Factory

 

 

Reset procedure.

 

btL (Battery Low)

fig.btL

Situation: Battery power used for saving parameter settings has been used up.

Action: Take the JV-1010 to your dealer or nearby Roland Service to have the battery exchanged.

Situation: A system exclusive message was not properly received. Repeated appearance of this same error message means that there is a problem with the MIDI message.

Action: Check the content of the received system exclusive message.

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Page For the U.K Page Using the Unit Safely Important Notes Power SupplyImportant Notes Additional PrecautionsQuick Start Contents Appendices SpecificationsPatch List Rhythm Set ListIncorporates the JV-1080 Sound Module Main FeaturesFront and Rear Panel Computer Switch Mac, PC-1, PC-2, Midi Midi Connectors IN, OUT, ThruComputer Connector Front and Rear PanelQuick Start Attaching the Rubber Feet Installing on the Rack-Mount AdaptorGetting Ready to Play Getting Ready to Play Installing a Wave Expansion BoardHow to Install a Wave Expansion Board 03a.e Position the board holders so they are orientedRotate the board holders to LOCK, securing the Wave Use the tool supplied with the Wave Expansion Board toExpansion Board in place Use the specified screws you removed in to reattachMidi OUT Making the ConnectionsConnecting a Midi keyboard or sequencer the Midi connectors Connecting audio equipment the Output jacks L MONO, RUsing headphones the Phones jack Using a computer the Computer connectorSwitching Off the Power Switching the Power On and OffSwitching On the Power Press the Value knob Turn the CATEGORY/BANK knob to choose Piano Factory ResetListening to Demo Songs Demo Play Press the Value knob or the Volume knobTurn the CATEGORY/BANK knob to choose Demo Turn the Value knob to choose the song you want to hearListening to Demo Songs Demo Play Composer ProfilesScott Wilkie Gundy Keller Hans-Joerg SchefflerWAVE-EXP Wave Expansion Board installed in the slot PRESET-D GM General MidiChoosing and Playing Patches SessionAuditioning Patches Phrase Preview Holding down the Volume knob, the sound for the currentlyChoosing and Playing Patches Selected patch is playedFinger some keys on the Midi keyboard to play a few notes Playing Notes from a Midi KeyboardTurn the Part knob and choose Choosing Patches by Bank Choosing PatchesChoosing Patches by Category Bright Piano by holding down the Volume knobTurn the CATEGORY/BANK knob to choose Piano Turn the Value knob to choosePlaying Percussion Sounds Turn the CATEGORY/BANK knob and choose a bank. Make Set the transmit channel for the Midi keyboardYour selection from the text displayed in white Turn the Value knob and choose a rhythm setPress the Value knob to switch to the GM mode GM Entering GM ModeSettings to an External Midi Device Data Transfer p To Performing Multiple Parts PerformanceSet the transmit channel on the external Midi device to Changing PatchesPatch Bank Select Program Group Number Changing Sounds from an External Midi DeviceChanging a Performance Press the Value knob and choose the Performance modePerformance Bank Select Program Group Number User PRESET-A PRESET-BChanging a Rhythm Set Rhythm Set Bank Select Program Group Number Transmit a Program Change message from the external MidiDevice to the JV-1010 refer to the following table Connecting to the Computer Connector Connecting to a ComputerTrying Out Desktop Music Two Ways to ConnectFor PCs Trying Out Desktop MusicFor Apple Macintosh Computers Computer cable sold separately RSC-15ATConnect the other end of the computer cable to the JV-1010’s Computer connectorConnecting with Midi Connectors Performance Performing Multiple Parts Performance ModeFor Part Press the Value knob to choose the Performance modeTurn the Value knob to choose patch Making Part Settings Part Editing Using Only the JV-1010Memory-Related Operations Utility Restoring the Factory Settings Factory ResetEditing Using Only the JV-1010 GM Initialize Initializing GM Mode GM InitializeTurn the CATEGORY/BANK knob to choose KEY&ORGAN Initialize Initializing the Settings InitializeDtr flashes on the display Selecting the Receive Channel Perform Ctrl CH Making System Settings SystemMaster Tune Tuning Master TuneAppendices Troubleshooting Error Messages No. Name Voice Key Assign User User Group PR-A Preset a GroupPatch List Patch List PR-B Preset B Group PR-C Preset C GroupPatch List PR-D GM Group PR-E Preset E Group Name Voice Patch List XP-A SessionKeyboard & Organ Group Patch Category ListPiano Piano Group Electric Guitar Patch Category List GUITAR/BASS Guitar/Bass GroupPatch Category List ORCH/BRASS Orchestra/Brass Group Hard Synth Lead Patch Category List SYNTH/PAD Synth/Pad GroupSoft Synth Lead Techno Synth Pulsating Synth Synth FX Noise etcPoly Synth Bright Pad Synth Soft Pad Synth Vox, Choir SYN Other Synth BPD Bright PAD SPD Soft PAD VOX VOXEthnic Group Rhythm & Sound Effects Group Patch Category ListRhythm Set List User User PR-A Preset a Group PR-B Preset B GroupRhythm Set List PR-C Preset C Group PR-D GM Group PR-E Preset E Group001 002 003 004 005 006 007 008 SessionSet Demo Drum XP-A SessionPerformance List User User Group PR-A Preset a Group PR-B Preset B GroupName Key Mode Data Reception Midi ImplementationChannel Voice Messages Polyphonic AftertouchMidi Implementation Channel Mode Messages System Exclusive Messages System Realtime MessagesData Transmission Data TransmissionData Request 1 RQ1 Data Set 1 DT1Data Set1 RPN MSB/LSB Controller number 100Identity Reply Message JV-1010 Model ID=6AH Midi Implementation Parameter Address MapSystem System CommonScale Tune Performance Common PerformancePatch Common Performance PartPatch Patch Tone INT, PCM, EXP Rhythm Note Rhythm SetupRhythm Common NO-SUS, Sustain OFF, CONTINUOUS, KEY-ON Address Block MapGS Model ID = 42H Supplementary Material Type18 MODULATION-DELAY Type17 STEREO-DELAYType19 TRIPLE-TAP-DELAY Type20 QUADRUPLE-TAP-DELAYType35 CHORUS→ Delay serial Type34 ENHANCER→ Delay serialType36 FLANGER→ Delay serial Type38 CHORUS/DELAY parallelExamples of Exclusive Messages Calculating the Checksum Examples of Actual Midi MessagesAscii Code Table Scale Tune Function Model ID 42H GS, address 40 1x 40HEqual Temperament Just Intonation tonic of CMidi Implementation Chart Specifications Computer Cable Wiring Diagrams Part IndexUser Utility IndexAvis Information Page 01891601 ’02-2-AE2-61N

JV-1010 specifications

The Roland JV-1010 is a compact and versatile synthesizer and sound module that has made a significant impact on the music production landscape since its introduction in the mid-1990s. Renowned for its extensive sound library and superior sound quality, the JV-1010 stands as a go-to device for musicians looking for a powerful yet portable instrument.

One of the standout features of the JV-1010 is its expansive sound engine, which houses 1,024 patches and 36 voices of polyphony. This allows for complex musical layers without the risk of cutting off notes. The built-in digital effects processor comes with 40 types of effects, including reverb, chorus, and flanger, enabling users to further enhance their sounds and create unique tonal textures.

The sound generation technology behind the JV-1010 is based on the JV-1080 platform, leveraging Roland's acclaimed 'SR-JV80' expansion board technology. This modular approach allows users to expand their sonic capabilities by adding additional sound banks, providing access to a wide range of genres and instruments. Notably, the synthesizer includes sounds from various musical traditions, from orchestral to electronic, making it suitable for diverse musical styles.

Another key characteristic of the JV-1010 is its user-friendly interface. It features a clear LCD screen and organized button layout, making it easy for musicians to navigate through its extensive library. Additionally, the unit supports MIDI connectivity, allowing it to seamlessly integrate with other MIDI-compatible gear, such as keyboards, drum machines, and computers. This makes the JV-1010 an excellent choice for studios and live performance settings alike.

The compact size of the JV-1010, which allows it to easily fit into a standard rack mount or travel setup, adds to its appeal, especially for mobile musicians. The lightweight design does not compromise its durability, ensuring it can withstand the rigors of frequent transport.

Overall, the Roland JV-1010 synthesizer is a powerhouse of sound engineering, providing musicians with a rich palette of tones and textures. Its robust feature set, expansion capabilities, and portability make it a timeless instrument that continues to be appreciated by both seasoned professionals and emerging artists in the music industry. Whether used for studio production, live performance, or sound design, the JV-1010 remains a reliable choice for those seeking high-quality musical tools.
Top Page Image Contents