Roland M-48 owner manual Attaching the Reac Connector Cover, Attaching the Ferrite Core

Page 15

Installation

Attaching the REAC Connector Cover

If you’re using a commercially available Cat5e Ethernet cable, attach the included REAC connector cover to the REAC port.

The REAC connector cover must be attached in order to minimize electromagnetic noise.

1Hook the included REAC connector cover over the tab of the REAC port.

REAC connector cover (included)

2Press the REAC connector cover straight in to fix it in place.

*Remove the REAC connector cover if you’ll be using an EtherCon type REAC cable.

Be careful not to lose the REAC connector cover that you removed.

Attaching the Ferrite Core

When making a REAC connection, you must attach the included ferrite core to the REAC cable.

The ferrite core must be installed in order to prevent electromagnetic noise.

1Spread the two tabs and open the ferrite core.

2Attach the ferrite core to the SC-W20F/SC-W100S/W100S-R REAC cable (sold separately) or the Cat5e Ethernet cable at a location near the connector (near the M-48).

Close the ferrite core around the cable, and press it shut until you hear the click.

Ferrite core (included)

Connector on the M-48 side

* Attach the ferrite core near the base of the RJ45 connector.

15

Image 15

Contents Copyright 2009 Roland Corporation Ferrite core Check the included ItemsMain Features Table of Contents Do not open or perform any internal modifications on Unit Never install the unit in any of the following locationsProtect the unit from strong impact. Do not drop it Never climb on top of, nor place heavy objects on the unitScrews for attaching the APC-33 all purpose clamp Can deform or discolor the unit Distance from this unit, or switch them offConnectors. Rough handling can lead to malfunctions Move it farther away from the source of interferenceTop Panel Panel DescriptionsMID Freq button Line OUT Volume knobPhones Volume knob Control select section LO Gain buttonRear Panel Attach the mounting bracket to the M-48 InstallationPlacing the M-48 on a Desk at an Angle Attaching the M-48 to the Top of a Mic Stand Attach the mounting bracket to the mic stand Installation If Your Mic Stand has 3/8 inch Threads Items to useIf Your Mic Stand has 5/8 inch Threads Below Attaching the M-48 to Any Part of a Mic StandAttach the APC-33 to your mic stand or drum, and fasten Mounting bracketAttaching the Reac Connector Cover Attaching the Ferrite CoreSpread the two tabs and open the ferrite core Connecting the M-48 to a V-Mixing System Connecting External DevicesConnecting External Devices Connecting the M-48 to an Analog Mixer SystemFront speakers 400 FOH Connecting Nine or More M-48 UnitsUnits 4000S-3208 Slave Reac deviceRear panel Connecting Input/Output Devices to the M-48Turning the Power Off Turning the Power OnMaking Settings for the M-48 Other settings settings made by the mixing engineer Example setup for the Drummer Source level/pan settingsGroups for the drummer Guitar2 L Example setup for lead vocalistGroups for the lead vocalist Guitar1 LGuitar1 L Guitar1 R Guitar2 L Guitar2 R Example setup for backing vocalistsSource assign settings Groups for backing vocalist Overhead LHere’s how to monitor just the audio of a specific group Adjusting the MixAdjusting the Volume of Each Group Press the Volume buttonTurn the AUX in knob to adjust the AUX in input level Adjusting the Pan of Each GroupAdjusting the Input Level of AUX Using the Built-in Ambient MicPress the Reverb Send button Using EffectsApplying Reverb to Each Group Applying EQ to Each GroupAdjusting the Line Out Output Level Applying a Limiter to the Headphones OutputUsing the Memory Functions Storing Mixer Settings to Memory StoreAbout Memory Press the Recall button Recalling Mixer Settings from Memory RecallReturning to the Factory Settings Factory Reset Turn off the power pDimensions Main SpecificationsBlock Diagram Troubleshooting Avis Other CENTRAL/ Latin America Information

Related manuals

Manual 2 pages 15.57 Kb