Roland M-48 owner manual Protect the unit from strong impact. Do not drop it

Page 6

USING THE UNIT SAFELY

006

●When using the unit with a mic stand, the rack or stand must be carefully placed so it is level and sure to remain stable. If not using a mic stand, you still need to make sure that any location you choose for placing the unit provides a level surface that will properly support the unit, and keep it from wobbling.

.................................................................................................................................

011

●Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit.

.................................................................................................................................

012d

●Immediately turn the power off, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page when:

•If smoke or unusual odor occurs

•Objects have fallen into, or liquid has been spilled onto the unit; or

•The unit has been exposed to rain (or otherwise has become wet); or

•The unit does not appear to operate normally or exhibits a marked change in performance.

.................................................................................................................................

013

●When using this device in an environment where children are present, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit.

.................................................................................................................................

014

●Protect the unit from strong impact. (Do not drop it!)

.................................................................................................................................

101c

●This device is designed so that it can be used with a microphone stand or with the APC-33 all-purpose clamp made by Roland. When using this device with a mic stand or the all-purpose clamp, placing it on an unstable location may cause the device to topple or fall, possibly damaging the device or causing personal injury.

.................................................................................................................................

101f

●Even if you observe the cautions listed in the owner’s manual, certain modes of use may produce the potential for this device to fall from the mic stand, or for the mic stand to topple over. Please exercise caution before using this product.

.................................................................................................................................

new

●When attaching or detaching the mounting bracket or bracket tray (p. 11–14), be careful not to injure yourself on the corners of the bracket or tray.

.................................................................................................................................

104

●Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children.

.................................................................................................................................

106

●Never climb on top of, nor place heavy objects on the unit.

.................................................................................................................................

108c

●Disconnect all cords coming from external devices before moving the unit.

.................................................................................................................................

118c

●Keep small parts such as the following out of reach of children so that they cannot be accidentally swallowed.

•Removed parts:

Screws for fastening the bracket tray

•Included items:

Ferrite core, REAC connector cover, Wing nut, Nut, Washers, Rubber washer, Screws for fastening the M-48,

and Screws for attaching the APC-33 all purpose clamp

.................................................................................................................................

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Copyright 2009 Roland Corporation Check the included Items Ferrite core Main Features Table of Contents Never install the unit in any of the following locations Do not open or perform any internal modifications on UnitProtect the unit from strong impact. Do not drop it Never climb on top of, nor place heavy objects on the unitScrews for attaching the APC-33 all purpose clamp Move it farther away from the source of interference Distance from this unit, or switch them offConnectors. Rough handling can lead to malfunctions Can deform or discolor the unitPanel Descriptions Top PanelControl select section LO Gain button Line OUT Volume knobPhones Volume knob MID Freq buttonRear Panel Attaching the M-48 to the Top of a Mic Stand InstallationPlacing the M-48 on a Desk at an Angle Attach the mounting bracket to the M-48Items to use InstallationIf Your Mic Stand has 3/8 inch Threads Attach the mounting bracket to the mic standIf Your Mic Stand has 5/8 inch Threads Mounting bracket Attaching the M-48 to Any Part of a Mic StandAttach the APC-33 to your mic stand or drum, and fasten BelowAttaching the Reac Connector Cover Attaching the Ferrite CoreSpread the two tabs and open the ferrite core Connecting External Devices Connecting the M-48 to a V-Mixing SystemConnecting the M-48 to an Analog Mixer System Connecting External Devices4000S-3208 Slave Reac device Connecting Nine or More M-48 UnitsUnits Front speakers 400 FOHConnecting Input/Output Devices to the M-48 Rear panelTurning the Power On Turning the Power OffMaking Settings for the M-48 Other settings settings made by the mixing engineer Example setup for the Drummer Source level/pan settingsGroups for the drummer Guitar1 L Example setup for lead vocalistGroups for the lead vocalist Guitar2 LOverhead L Example setup for backing vocalistsSource assign settings Groups for backing vocalist Guitar1 L Guitar1 R Guitar2 L Guitar2 RPress the Volume button Adjusting the MixAdjusting the Volume of Each Group Here’s how to monitor just the audio of a specific groupUsing the Built-in Ambient Mic Adjusting the Pan of Each GroupAdjusting the Input Level of AUX Turn the AUX in knob to adjust the AUX in input levelApplying EQ to Each Group Using EffectsApplying Reverb to Each Group Press the Reverb Send buttonApplying a Limiter to the Headphones Output Adjusting the Line Out Output LevelUsing the Memory Functions Storing Mixer Settings to Memory StoreAbout Memory Turn off the power p Recalling Mixer Settings from Memory RecallReturning to the Factory Settings Factory Reset Press the Recall buttonMain Specifications DimensionsBlock Diagram Troubleshooting Avis Information Other CENTRAL/ Latin America
Related manuals
Manual 2 pages 15.57 Kb
Top Page Image Contents