Roland owner manual Connecting External Devices, Connecting the M-48 to a V-Mixing System

Page 16

Connecting External Devices

Connecting the M-48 to a V-Mixing System

Lead Vocal

Vocal 1

Vocal 2

Vocal 3

Keyboard

Guitar

Bass

Drum

M-48 x 8

REAC cable or Cat5e Ethernet cable

16 channels of audio input

REAC port 3 4 5 6 7 8 9 10

REAC port 1

2

S-4000D

		16 channels of audio input
	S-1608 (Slave REAC device)
		S-1608 (Slave REAC device)
		REAC port
	8 channels of	REAC port
	8 channels of
	audio output
	Front speakers	REAC cable or
	Front speakers	Cat5e Ethernet cable
		Cat5e Ethernet cable
		8 channels of audio output

REAC A port

REAC B port

M-400 (FOH)

*The M-400 must be running system software version 2.0 or later.

*The M-48 can be set and managed from the M-400 only if the M-48 is connected to the M-400’s REAC B port via the S-4000D.

*In order to maintain the transmission quality of the digital REAC signal, use fully approved Cat5e Ethernet cable such as the 20 meter or 100 meter REAC cables (SC-W20F/SC-W100S/W100S-R; sold separately).

16

To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.

Image 16

Contents Copyright 2009 Roland Corporation Check the included Items Ferrite coreMain Features Table of Contents Never install the unit in any of the following locations Do not open or perform any internal modifications on UnitNever climb on top of, nor place heavy objects on the unit Protect the unit from strong impact. Do not drop itScrews for attaching the APC-33 all purpose clamp Distance from this unit, or switch them off Connectors. Rough handling can lead to malfunctionsMove it farther away from the source of interference Can deform or discolor the unitPanel Descriptions Top PanelLine OUT Volume knob Phones Volume knobControl select section LO Gain button MID Freq buttonRear Panel Installation Placing the M-48 on a Desk at an AngleAttaching the M-48 to the Top of a Mic Stand Attach the mounting bracket to the M-48Installation If Your Mic Stand has 3/8 inch ThreadsItems to use Attach the mounting bracket to the mic stand If Your Mic Stand has 5/8 inch Threads Attaching the M-48 to Any Part of a Mic Stand Attach the APC-33 to your mic stand or drum, and fastenMounting bracket BelowAttaching the Ferrite Core Attaching the Reac Connector CoverSpread the two tabs and open the ferrite core Connecting External Devices Connecting the M-48 to a V-Mixing SystemConnecting the M-48 to an Analog Mixer System Connecting External DevicesConnecting Nine or More M-48 Units Units4000S-3208 Slave Reac device Front speakers 400 FOHConnecting Input/Output Devices to the M-48 Rear panelTurning the Power On Turning the Power OffMaking Settings for the M-48 Other settings settings made by the mixing engineer Source level/pan settings Example setup for the DrummerGroups for the drummer Example setup for lead vocalist Groups for the lead vocalistGuitar1 L Guitar2 LExample setup for backing vocalists Source assign settings Groups for backing vocalistOverhead L Guitar1 L Guitar1 R Guitar2 L Guitar2 RAdjusting the Mix Adjusting the Volume of Each GroupPress the Volume button Here’s how to monitor just the audio of a specific groupAdjusting the Pan of Each Group Adjusting the Input Level of AUXUsing the Built-in Ambient Mic Turn the AUX in knob to adjust the AUX in input levelUsing Effects Applying Reverb to Each GroupApplying EQ to Each Group Press the Reverb Send buttonApplying a Limiter to the Headphones Output Adjusting the Line Out Output LevelStoring Mixer Settings to Memory Store Using the Memory FunctionsAbout Memory Recalling Mixer Settings from Memory Recall Returning to the Factory Settings Factory ResetTurn off the power p Press the Recall buttonMain Specifications DimensionsBlock Diagram Troubleshooting Avis Information Other CENTRAL/ Latin America

Related manuals

Manual 2 pages 15.57 Kb